Barbell Collar Types
Barbell collars come in four kinds covered here: spring clips you squeeze open, spinlock collars that screw onto a threaded sleeve, lever or lock-jaw clamps that close with a latch, and competition collars that tighten with a screw or lever and weigh 2.5 kg each under IPF rules. Each is sized for a sleeve of about 1 inch or 2 inch, so match the collar to your bar's sleeve and check for threads before you buy.
A barbell collar is the clamp that goes on the sleeve outside your plates so they stay put. This guide covers four kinds: spring clips you squeeze open, spinlock collars that screw onto a threaded sleeve, lever or lock-jaw clamps that close with a latch, and competition collars that tighten with a screw or lever and weigh 2.5 kg each under IPF rules. Each collar is sized for a sleeve of about 1 inch or 2 inch, and some collars for standard bars are sold for 1-1/16 inch or 27 mm bars, as Ivanko's are. Every figure below is the maker's own or the rule book's, read on 17 Nov 2026. For the two sleeve sizes themselves, see Olympic vs standard barbell.
The four types at a glance
The table sums up how each type holds plates and which sleeve sizes we found it made for, on the makers' pages listed in the next section. The names are not used one way across makers, so read each listing for the sleeve size and, for a spinlock, the word threaded.
| Type | How it holds plates | Sleeve sizes we found | Needs a threaded sleeve | Weight the makers state |
|---|---|---|---|---|
| Spring clip | A spring. Squeeze the handles to open it, slide it on, let go and it grips the sleeve | 1 inch (York), 2 inch (York, CAP), 27 mm (Ivanko) | No | None of the four pages states the collar's own weight |
| Spinlock | A threaded collar you spin along the bar's threaded end until it seats against the outer plate | 1 inch (York, CAP's threaded bar) | Yes | None stated. York lists only a shipping weight |
| Lever or lock-jaw clamp | A latch or lever closes the collar around the sleeve in one motion | 1 inch (York, Lock-Jaw), 2 inch (Lock-Jaw, CAP) | No | None stated. York lists only a shipping weight |
| Competition collar | A 2.5 kg metal collar tightened by a screw, a wheel, a compression ring or a locking lever | 2 inch (Eleiko's 50 mm hole; IPF bar sleeves of 50 to 52 mm) | No | 2.5 kg each: the IPF rule, Eleiko's 2500 g, Ivanko's 5 kg per pair |
Read on makers' own pages and the IPF Technical Rulebook on 17 Nov 2026. Collars outside these four exist, for example Ivanko's compression ring and bolt collars in the next table.
What makers state for each collar
We opened makers' own pages for 17 collars from five companies on 17 Nov 2026. Only Ivanko and Eleiko print a weight for the collar itself. York prints a shipping weight, which is the boxed item, not the collar, and CAP and Lock-Jaw print no weight. A sleeve size in the table is the maker's wording; where a page gives no size field, we say what the product name says.
| Maker | Collar | Type | Sleeve it is made for | Weight the maker states |
|---|---|---|---|---|
| Spring clips | ||||
| York Barbell | 1" Spring Collars w/ Rubber Grips, SKU 6135, pair | Spring clip | 1 inch, per the product name and its 1" Standard Collars category | No collar weight. Shipping weight 1 lb for the pair |
| York Barbell | 2" Spring Collars w/ Rubber Handles, SKU 36040, pair | Spring clip | 2 inch, for "your Olympic barbell" | No collar weight. Shipping weight 2.5 lbs |
| CAP | Olympic Spring Clip Barbell Collars OC-06A, pair | Spring clip | "accommodate 2 in diameter bars" | None stated |
| Ivanko | CS-27T | Spring clip | 27 mm bars | None stated |
| Spinlock and threaded collars | ||||
| York Barbell | 1" Spin-Lock Collar, SKU 6088, sold one at a time | Spinlock, with a rubber gasket | "your 1" standard spin-lock barbell" | No collar weight. Shipping weight 0.5 lbs |
| CAP | Star collars sold with the Standard Threaded Bar RB-60T | Collar for a threaded end | 1 inch: the bar "Accommodates 1-inch standard plates" and has "threaded ends" | None stated |
| Ivanko | CTS replacement threaded collar | Threaded | Ivanko bars and handles that "must have an Acme-threaded handle" | None stated |
| Lever and lock-jaw clamps | ||||
| York Barbell | 1" Muscle Clamp Collars, SKU 36046, pair | Single motion lock and unlock, rubber lined | 1 inch, per the product name and its 1" Standard Collars category | No collar weight. Shipping weight 2 lbs |
| Lock-Jaw | Sport, sold as a set of two | Latch clamp, resin | 1"/25mm or 2"/50mm, two size options on one listing | None stated |
| CAP | 2-Inch Olympic Bar Clamps OC-11B, set of 2 | Clamp, plastic resin | Olympic size bars | None stated |
| Bolt and compression ring collars (Ivanko, standard bars) | ||||
| Ivanko | CC-3, "compression-ring collar w/spin-lock" | Compression ring | 1-1/16" bars | 2.625 lbs each |
| Ivanko | CL-1/4, "compression-ring collar w/t-bolt" | Compression ring, T-bolt | 1" and 1-1/16" bars | 0.4 lbs each |
| Ivanko | C-1 outside collar | Not stated | 1" bars | 1 lb |
| Ivanko | COS-2-1/2 outside collar | Not stated | 1" and 1-1/16" bars | 2-1/2 lb |
| Competition collars | ||||
| Eleiko | IPF Powerlifting Competition Barbell Collars 3001681, pair | Quick turn screw | Hole diameter 50 mm (1.97 in) | 2500 g each, calibrated to +10 g / -0 g; 5 kg the pair |
| Eleiko | Competition Collar 3085701, pair | Indexed locking lever and tightening wheel | Not stated on the sheet | 5 kg (11.02 lbs) the pair, tolerance -0/+10 g |
| Ivanko | CO-2.5KG Olympic Pressure Ring Collar, pair | Compression ring | Olympic sleeves; takes about 74 mm of sleeve | 5 kg per pair |
Makers' own pages and product sheets, opened 17 Nov 2026. We weighed none of these collars. York's figures are shipping weights from its product pages, so they include packaging. Ivanko writes weights as each or per pair as shown. Rogue's pages and Mirafit's collar pages refused our requests that day, so neither is in the table.
Spring collars vs spinlock collars
The difference is the bar end. A spring clip grips a plain, smooth sleeve, and York's 1 inch and 2 inch spring collars go on "with just a squeeze of the handles". A spinlock screws onto the bar end, so it works only on a bar whose ends are threaded to match. The makers' pages we read show this pairing rather than spell it out: CAP sells its Standard Threaded Bar RB-60T with "threaded ends and included star collars", and York describes its 1 inch spin-lock collar as made for a "1" standard spin-lock barbell". Ivanko's threaded collar goes only on a bar that "must have an Acme-threaded handle", which shows that thread form matters too, not just the word threaded.
Two cautions from the pages we read. First, the name spin-lock is not used one way: Ivanko calls its CC-3 a "compression-ring collar w/spin-lock", and its page does not say it needs a threaded bar. Second, a 1 inch bar is not always exactly 1 inch: Ivanko lists collars for "1-1/16" bars" next to ones for 1 inch bars. So check two things before you buy a spinlock: that your bar's ends are threaded, and that the collar is sold for that bar or that thread.
Which to pick: if your bar has threaded ends and came with spinlocks, replace like with like. If the sleeves are smooth, a spinlock has nothing to screw onto, so choose a spring clip or a clamp sized for your sleeve.
Spring clips vs clamp collars
Both go on a plain sleeve, and both come in 1 inch and 2 inch versions from the makers above. They differ in how they close and what they are made of.
- Spring clips are springs you squeeze to open and release to grip. York's are chrome plated steel with rubber handles, and CAP's OC-06A is chrome plated with "easy grip handles".
- Lever or lock-jaw clamps close with a latch or lever. Lock-Jaw's Sport has an "over-sized latch" for one-handed use and is made of composite resin. CAP's OC-11B is a plastic resin clamp. York's 1 inch Muscle Clamp is a "single motion lock/unlock collar" with a rubber inner lining.
We have not tested how hard any collar holds, and none of the makers' pages we read gives a holding force in pounds or newtons, so this guide does not rank them on grip. If you choose a clamp, make sure the version matches your sleeve: Lock-Jaw sells its Sport in a 1"/25mm size and a 2"/50mm size on the same listing, so pick the size that matches your sleeve when you order.
Competition collars
The IPF Technical Rulebook, effective 1 March 2026, says in section 2.4 that collars "Shall always be used" and "Must weigh 2.5 kg each". Its bar rules put the sleeve diameter at 50 to 52 mm and say "Weight of the bar and collars are to be 25 kg". So competition collars are a 2 inch item: none of the three competition collars we read is sold for a 1 inch sleeve.
Makers match the rule in their own figures. Eleiko's IPF collars 3001681 are "calibrated to within +10 g / - 0 g for each 2500 g collar", have a 50 mm hole and tighten with "a quick turn screw fastening system". Eleiko's newer Competition Collar 3085701 is certified by the IWF, IPF and WPPO, weighs 5 kg the pair and locks with an indexed lever and tightening wheel; Eleiko says its slimmer design "adds 33 mm of loadable space on the sleeve" for IPF use. Ivanko's CO-2.5KG pressure ring collar weighs 5 kg per pair and takes about 74 mm of sleeve; Ivanko lists it as approved by IPL/USPA, WPC/APC and AAU, and its page does not list the IPF.
For a home lifter this matters in one way: a pair of competition collars adds 5 kg to the bar, so count it. Spring clips and clamps add some weight too, but the makers above state none for theirs, so if you want to count yours, weigh them on a scale that reads small weights. For plates and bars, see how to weigh your weights.
How to use barbell collars
- Match the sleeve. Check whether your bar is a 1 inch or 2 inch bar with the quarter test in Olympic vs standard barbell. A collar for one size does not fit the other.
- Load the plates and push them inward. Slide each plate on until the stack sits against the inner collar, with no gap between plates.
- Put the collar on flush against the last plate. For a spring clip, squeeze the handles, slide it on and let go. For a clamp, open the latch or lever, slide it on and close it. For a spinlock, spin it along the threads until it seats against the plate. For a competition collar, slide it on and turn the screw or wheel, or close the lever, as its maker describes.
- Collar both ends, every set. CAP says collars help "make sure that the weight plates you use do not slip off of your workout bar". In IPF competition, collars "Shall always be used".
- Check after each set. If a collar has moved away from the plates, push it back before the next set.
- Take collars off before changing plates. Then put them back on the new outer plate.
Which collars fit our bars
We sell Signature Fitness 1 inch standard bars in 5, 6 and 7 ft lengths in our store. Each has two fixed inner collars and comes with no outer collars. We have not yet measured the sleeve diameter with calipers, checked whether the ends are threaded or fit-tested any outer collar on them, so we do not say which collar type or product fits them. We will update this section after the fit test.
Until then, for any 1 inch bar you own: look at the ends for threads, measure the sleeve, and buy a collar whose maker names that sleeve size. For what goes between the collars, see what weight plates do I need.
Short answers
What are barbell collars?
Barbell collars are clamps that go on the bar's sleeve outside the plates so the plates do not slip off. Some bars, ours included, also have fixed inner collars that are part of the bar; outer collars are the ones you put on and take off. The outer kinds covered here are spring clips, spinlock collars, lever or lock-jaw clamps and competition collars.
What are the best barbell collars?
The right collar is the one made for your sleeve size and bar end, and no single type is right for every bar. A spinlock needs a threaded sleeve; a spring clip or clamp goes on a plain one; competition collars are 2 inch and weigh 2.5 kg each under IPF rules. We have not tested holding force, and the makers we read publish none, so we rank no product.
Spring collars vs spinlock: what is the difference?
A spring collar grips a smooth sleeve when you release its handles, while a spinlock screws onto threads at the bar's end. A spinlock only works on a threaded bar, and a spring clip is for a plain sleeve of its size.
Spring clips vs clamp collars: which should I use?
Either works on a plain sleeve if it is made for that sleeve size. Spring clips are springs you squeeze open; lever or lock-jaw clamps close with a latch, and the ones we read are resin or rubber lined. No maker we read gives a holding force, so choose by fit and how you like to load the bar.
Which collars fit BASALT's bars?
We do not say yet. Our Signature Fitness 1 inch bars have two fixed inner collars and no outer collars, and we have not checked whether their ends are threaded or fit-tested any outer collar. This answer will change when that test is done.
Related: Olympic vs standard barbell for the two sleeve sizes, do standard plates fit an Olympic bar, what weight plates do I need, how to weigh your weights, and our store.
Sources
We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.
- IPF Technical Rule Book (effective 01 March 2026), version 3, International Powerlifting Federation. Used for: Section 2.4 Collars: collars "Shall always be used" and "Must weigh 2.5 kg each"; bar rules: sleeve diameter 50 to 52 mm ("not to exceed 52 mm or be less than 50 mm"); "Weight of the bar and collars are to be 25 kg".. Checked .
- 1" Spring Collars w/ Rubber Grips (pair), York Barbell. Used for: York 1 inch spring collar, SKU 6135: "With just a squeeze of the handles" it secures plates on a standard barbell; steel, chrome plated, rubber handles; sold in pairs; 1" Standard Collars category; shipping weight 1 lbs, no collar weight stated.. Checked .
- 2" Spring Collars w/ Rubber Handles, York Barbell. Used for: York 2 inch spring collar, SKU 36040: secures plates "onto your Olympic barbell" with a squeeze of the handles; sold in pairs; shipping weight 2.5 lbs, no collar weight stated.. Checked .
- CAP Olympic Spring Clip Collars, Pair, 2 in (OC-06A), CAP. Used for: CAP OC-06A spring clip: "accommodate 2 in diameter bars", sold as a pair, "Chrome plated and easy grip handles"; no weight stated.. Checked .
- Reg-Collars Collars for standard bars, 1 & 1-1/6 in., Ivanko Barbell Company. Used for: Collars for standard bars include sizes other than exactly 1 inch: CS-27T spring collars for 27mm bars; CTS replacement threaded collar for bars that "must have an Acme-threaded handle"; CC-3 "compression-ring collar w/spin-lock" for 1-1/16" bars, 2.625 lbs each; CL-1/4 "compression-ring collar w/t-bolt" for 1" and 1-1/16" bars, 0.4 lbs each; C-1 outside collar for 1" bars, 1 lb; COS-2-1/2 outside collar for 1" and 1-1/16" bars, 2-1/2 lb.. Checked .
- 1" Spin-Lock Collar, York Barbell. Used for: York 1 inch spin-lock collar, SKU 6088: rubber gasket "for a secure hold on your 1” standard spin-lock barbell"; sold individually; shipping weight 0.5 lbs, no collar weight stated.. Checked .
- CAP Standard 1-in Threaded Bar with Star Collars - Chrome or Black, CAP. Used for: CAP RB-60T: "The threaded ends and included star collars"; "Accommodates 1-inch standard plates"; "Solid bar has chromed finish and threaded ends".. Checked .
- 1″ YORK Muscle Clamp Collars, York Barbell. Used for: York 1 inch Muscle Clamp, SKU 36046: "single motion lock/unlock collar", rubber inner lining, sold in pairs, 1" Standard Collars category; shipping weight 2 lbs, no collar weight stated.. Checked .
- Lock-Jaw Sport Barbell Collar, Lock-Jaw. Used for: Lock-Jaw Sport: sizes 1"/25mm and 2"/50mm, offered as size options on the same listing; "over-sized latch" to clamp and remove with one hand; composite reinforced resin; sold in sets of two; no weight stated.. Checked .
- CAP 2" Barbell Clamp Collars (OC-11B), CAP. Used for: CAP OC-11B: made to fit Olympic size bars; "quickly clamped on and off"; "special plastic resin"; set of 2; "help make sure that the weight plates you use do not slip off of your workout bar"; no weight stated.. Checked .
- Eleiko IPF Powerlifting Competition Barbell Collars, pair (product sheet, article 3001681), Eleiko. Used for: "calibrated to within +10 g / - 0 g for each 2500 g collar"; collars add 5 kg; hole diameter 50 mm / 1.97 in; "a quick turn screw fastening system"; IPF certified; sold in pairs.. Checked .
- Eleiko Competition Collar, pair (product sheet, article 3085701), Eleiko. Used for: Certified by IWF, IPF and WPPO; indexed locking lever and knurled tightening wheel; tolerance of -0/+10g; weight 5 kg / 11.02 lbs the pair; sold in pairs; no sleeve diameter stated.. Checked .
- Competition Collar, pair | Eleiko, Eleiko. Used for: "For IPF, the slimmer design adds 33 mm of loadable space on the sleeve.". Checked .
- CO-2.5KG Olympic Pressure Ring Collar - Grey - Pair, Ivanko Barbell Company. Used for: Compression-ring Olympic collars for competition; "Weight: 5 kg per pair"; "Space taken on bar sleeve: 2-29/32 (abt. 74mm)"; "IPL/USPA, WPC/APC & AAU Approved" (IPF not listed).. Checked .