Signature Fitness 1 inch standard bars, 5, 6 and 7 ft, are available now on eBay. Checkout on this site opens later.

How to Store Weight Plates

Store weight plates off the floor on a plate tree, a wall rack or your rack's horns, with posts that match the hole in your plates: 1 inch posts for standard plates, horns sized for 2 inch plates (REP's are 1.8 in across) for those. Put bumpers on long horns or a toast rack, keep every plate indoors and dry, and take plates off the bar after each session. Makers' stated total capacities run from 550 lb to 1,000 lb.

Updated . By the BASALT editorial team.

Store plates off the floor, on a plate tree, a wall rack or the horns on your rack, and match the post to the hole in your plates: a 1 inch post for standard plates, a horn sized for 2 inch plates for those. Put bumper plates on long horns or a toast rack, keep every plate indoors and dry, and take plates off the bar when you finish. The figures below are the makers' own, read on 17 Nov 2026. We tested none of these racks.

Match the post to the hole in your plates

The first thing to get right is size. Plates come with two hole sizes, and storage is built for one or the other. A plate only goes on a post that is narrower than its hole.

Makers' own figures, read on 17 Nov 2026 from the page linked in each row. We measured none of these.
ItemMaker and modelWhat the maker states
Plate holes
1 inch standard plateCAP Standard 1in Cast Iron Plate (RPG#2)"Accommodates all 1 in standard barbells and dumbbell handles"
2 inch plateCAP Olympic Cast Iron Plate (OPG#2)"2-in center hole"
2 inch plateTitan 25 LB Pair Cast Iron Olympic PlateCollar opening 50.5 mm, plus or minus 0.2 mm
2 inch plateREP Old School Iron Plates"The 52mm center hole fits all Olympic barbells"
Storage posts
1 inch plate treeBody-Solid SWT14"Holds Standard Plates (1” diameter hole)", six plate horns
Rack horns for 2 inch platesREP Weight HornsHorn diameter 1.8 in on the 1000, 4000 and 5000 Series versions
Wall rack for 2 inch platesTitan Wall Mounted 4-Peg rackWeight sleeve diameter 49 mm
Plate tree for 2 inch platesBody-Solid GOWTSix posts it lists as "2” x 8”"

What follows from the table:

If you are not sure which plates you have, our guide to Olympic vs standard barbells explains the two sizes, and do standard plates fit an Olympic bar covers mixing them.

What storage makers state

We read makers' own pages and data sheets for nine plate storage products on 17 Nov 2026. Capacity is stated three ways: as a total for the whole unit, as a limit per peg, or as a count of plates. Three of the nine state no capacity of any kind, and REP gives plate counts for its horns but no weight. A rating is the maker's claim about its own product, not a figure we checked.

TypeMaker and modelPlatesCapacity as the maker states itPosts and size
Plate treeBody-Solid SWT141 inch1,000 lb in the data sheet. The product page states no capacitySix posts. 27 x 16 x 24 in. The data sheet says it weighs 20 lb, the product page 17 lb
A-frame rackCAP RK-1BB1 inchNone stated on CAP's page"Accommodates 1-inch plates". No post count or size stated
Plate treeBody-Solid GOWT2 inch1,000 lbSix posts, 8 in. 20 x 23 x 40 in, 31 lb
Plate treeREP Bar and Weight Plate Tree2 inch, bumper and iron850 lbSix horns, usable length 8 in per side. 24 x 24 x 50 in, 35 lb
Freestanding rackBody-Solid GWT762 inch, bumper and ironNone stated8 horns set up for bumper plates or 10 for traditional plates, each 8 1/4 in. 121 lb
Wall rackTitan Wall Mounted 4-Peg rack2 inch800 lb in all, up to 200 lb per sleeve, "four 45 LB plates per post with room to spare"Four sleeves, 9.5 in long. 74 in tall, 10.5 in from the wall
Wall rackREP Wall Mounted Plate Storage2 inchNone statedHorns 8.25 in long. Single horn for full size plates, double horn for change plates
Rack hornsREP Weight Horns2 inchPlate counts only: three 45 lb bumpers or five 45 lb iron plates on the 1000 Series horn1.8 in across. 9 in (1000 Series), 6 in and 12 in (4000 and 5000 Series)
Toast rackTitan Horizontal Weight Plate Storage With WheelsBumpers550 lb8 pockets, small 8.5 in and large 11.75 in wide. 54 x 16 x 12.5 in, 44 lb

Makers' own figures, read on 17 Nov 2026. Sizes are length x width x height as each maker gives them. Rogue's product page and support guide for its Vertical Plate Tree 2.0 did not load for us, so Rogue is not in the table.

Body-Solid's data sheet and product page for the SWT14 disagree on its weight, and only the data sheet gives a capacity. When a maker's page is silent or contradicts itself, ask the maker in writing before you load the rack heavily.

Plate trees

A tree is the simplest choice if you have floor space and no rack: plates go on short posts around a central upright. Body-Solid says the SWT14's design "directs the weight load to the center reducing the risk of tipping", and says the GOWT's "central weight load distribution" does the same job.

No tree maker page that opened for us gave a loading order. The habit that follows from Body-Solid's center-load idea is to keep both sides of the tree close to the same weight as you add and remove plates, and to stay within the stated capacity.

Count by thickness as well as weight. A post holds as many plates as its length allows, and REP's horn figures show how much that changes with plate type: its 1000 Series horn, listed at 9 in in the specs and 8.9 in in the text, takes three 45 lb bumpers or five 45 lb iron plates.

Wall racks and vertical racks

A wall rack frees floor space, but it depends on what it is fixed to. REP's Wall Mounted Plate Storage is built for "16” stud mount spacing". Titan's 4-peg rack uses "Dual wall and floor anchors" and rests at an angle against the wall, and Titan says the dual anchor design "reduces wall stud stress". Follow the maker's mounting instructions and use the hardware it names.

If you rent, drilling into studs may not be allowed. Our apartment home gym guide covers what renters can and cannot do, and a freestanding tree avoids the question.

Horns on your rack

Horns bolt or hook onto a power rack's uprights and keep plates next to the bar. REP says its 1000 Series horns mount to the uprights "like a J-cup" with no hardware needed, and its 4000 and 5000 Series horns bolt on. Check that the horns are made for your rack model: REP sells its Weight Horns in versions for its 1000, 4000 and 5000 Series power racks, and says each version is slightly different to suit its rack.

Do not use the bar as storage. Eleiko says "Do not store bars with weights loaded as this could cause the bar to bend", and REP warns against "leaving a bar loaded with weight plates while racked for long periods". Strip the bar when you finish and put the plates on their posts.

How to store bumper plates

Bumpers need more post length than iron plates of the same weight: on every horn REP lists, fewer 45 lb bumpers fit than 45 lb iron plates. Body-Solid's GWT76 also takes fewer horns when set up for bumper plates, 8 against 10 for traditional plates. The other option is a toast rack, which holds bumpers in pockets: Titan's has 8 pockets in two widths, 8.5 in and 11.75 in, and a 550 lb capacity.

Makers do not agree on where bumpers can live, so read your own maker's care page:

We found no maker page that gives a safe height for stacking bumpers flat on the floor, so we give none. If you stack them, a rack built for the job is the safer place, and our bumper vs iron plates guide covers whether you need bumpers at all.

Small plates

REP's wall rack has a double horn just for change plates, and REP says full size plates "will not fit" on it. Titan's toast rack has narrower small pockets alongside the large ones. On a 1 inch tree, give the small plates their own post so they are easy to find. Small plates matter for steady progress, which our what plates do I need guide explains.

Rust in a garage

REP's maintenance guide says garage and basement gyms are "especially vulnerable because these spaces often have poor insulation and temperature swings that create condensation", and that corrosion of steel speeds up "significantly when relative humidity exceeds 50 to 60 percent." Its guide, written for home gym gear in general, suggests:

A cheap hygrometer tells you whether your garage sits above the range REP names. Plate finishes differ: CAP says its standard plates' baked enamel finish "prevents chipping and peeling", which is a claim about the paint, not a promise of no rust where the paint is gone.

The floor

Plates on the floor get chipped and tripped over. REP's guide says "leaving plates scattered across the floor is a recipe for damage" and lists "chips, scratches, bent handles, and tripping hazards". Body-Solid and CAP both describe their racks as keeping plates off the floor. If plates have to sit on the floor for now, keep them in one place out of walkways, and see our home gym flooring guide for mats. This page gives no figure for what a floor can hold.

What to check on your own gear

  1. The hole in your plates, 1 inch or 2 inch, and a post that matches it.
  2. The post's usable length, which decides how many plates fit, bumpers above all.
  3. The capacity and how it is stated: total, per peg, plate count, or none.
  4. Mounting: studs, anchors or a matching rack model, as the maker specifies.
  5. The room: indoors and dry, and your plate maker's own advice on heat, sun and moisture.
  6. The bar: empty at the end of every session.

Short answers

What is the best way to store weight plates at home?

On a plate tree, a wall rack or your rack's horns, with posts that match the hole in your plates. Keep them indoors and dry, and take them off the bar after each session. Eleiko and REP both warn that leaving a bar loaded can bend it.

Can I store 1 inch plates on rack horns?

Not on horns sized for 2 inch plates. REP's horns are 1.8 in across, wider than a 1 inch hole. Use a tree or rack sold for 1 inch plates, such as the Body-Solid SWT14, which its data sheet rates at 1,000 lb.

How should I store bumper plates?

On long horns or a toast rack built for bumpers, indoors and dry. Bumpers take more post length than iron: REP's 1000 Series horn holds three 45 lb bumpers or five 45 lb iron plates. Eleiko says its discs should be stored dry at about 18 to 27 C, while Homegrown Lifting says its URA-MAX bumpers are safe outdoors, so read your plate maker's care page.

How do I stop weight plates rusting in a garage?

Keep the air dry and the metal dry. REP's maintenance guide says steel corrosion speeds up when relative humidity exceeds 50 to 60 percent, and suggests a dehumidifier, desiccant packs, a light coat of 3-in-1 oil on bare metal, and drying gear after cleaning.

How much weight can a plate tree hold?

Only what its maker states. Body-Solid's data sheets rate its SWT14 and GOWT trees at 1,000 lb, and REP rates its Bar and Weight Plate Tree at 850 lb. Across the nine storage products in our table, the stated totals run from 550 lb for Titan's toast rack to 1,000 lb. Titan's wall rack also states 200 lb per sleeve, and three products state no capacity of any kind.

Related: what plates do I need, apartment home gym, home gym flooring and noise, and our 1 inch standard barbells; also how to clean a barbell and remove rust and weight plate dimensions.

Sources

We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.

  1. CAP Standard 1in Cast Iron Plate, Gray (RPG#2), CAP Barbell. Used for: CAP's 1 inch plates: "Accommodates all 1 in standard barbells and dumbbell handles"; "They are designed to be used with 1 in bars.". Checked .
  2. CAP Olympic Cast Iron Plate, Gray (OPG#2), CAP Barbell. Used for: CAP's 2 inch plates: "2-in center hole".. Checked .
  3. 25 LB Pair Cast Iron Olympic Plate, Titan Fitness. Used for: Titan plate collar opening 50.5 mm plus or minus 0.2 mm; "fits standard 2\" Olympic barbells".. Checked .
  4. Old School Iron Plates, REP Fitness. Used for: REP plate hole: "The 52mm center hole fits all Olympic barbells.". Checked .
  5. SWT14 Standard Plate Tree (product data sheet), Body-Solid. Used for: SWT14: "Holds Standard Plates (1” diameter hole)", six plate horns, 1000 lbs of weight capacity, weight 20 lbs, 27 x 16 x 24 in, EZ-Load design "directs the weight load to the center, reducing the risk of tipping".. Checked .
  6. Weight Horns | REP Fitness | Rack Attachments, REP Fitness. Used for: Horn diameter 1.8 in for 1000, 4000 and 5000 Series; length 9 in (1000 Series, described as 8.9 in in the text), 6 in and 12 in (4000 and 5000); 1000 Series holds three 45 lb bumpers or five 45 lb irons; 4000 Series four 45 lb bumpers or eight 45 lb irons; 5000 Series four 45 lb bumpers or seven irons; 1000 Series mounts "like a J-cup", no hardware needed; 4000 and 5000 bolt on; available in versions for the 1000, 4000 and 5000 Series power racks, each "slightly different to work best with the respective racks".. Checked .
  7. Wall Mounted 4-Peg Olympic Bumper Plate Weight Rack, Titan Fitness. Used for: Sleeve diameter 49 mm, sleeve length 9.5 in, 800 lb capacity, up to 200 pounds per sleeve, "four 45 LB plates per post with room to spare", 74 in tall, 10.5 in from wall, "Dual wall and floor anchors", "Dual-anchor design reduces wall stud stress", angled design.. Checked .
  8. GOWT Olympic Weight Plate Tree (product data sheet), Body-Solid. Used for: GOWT: six "2” x 8”" posts, 1,000 lbs capacity, 20 x 23 x 40 in, 31 lbs, "central weight load distribution", plates "suspended off the floor".. Checked .
  9. 1" Standard EZ-Load Weight Plate Tree SWT14 - Storage Racks, Body-Solid. Used for: SWT14 product page: six storage posts, 27 x 16 x 24 in, 17 lbs, no capacity stated, "directs the weight load to the center reducing the risk of tipping".. Checked .
  10. CAP A-frame Standard Plate Storage Rack, Dark Gray (RK-1BB), CAP Barbell. Used for: RK-1BB: "Accommodates 1-inch plates", "Keep your weight plates in order and off the floor"; no capacity, post count or post size stated.. Checked .
  11. Bar and Weight Plate Tree | REP Fitness, REP Fitness. Used for: 850 lb capacity, six weight horns that fit bumper and iron plates, usable horn length 8 in per side, 24 x 24 x 50 in, 35 lb.. Checked .
  12. GWT76 High Capacity Olympic Plate Rack (product data sheet), Body-Solid. Used for: GWT76: 8 horns as a bumper plate rack or 10 as a traditional Olympic plate tree, each 8 1/4 in (no reason given for the difference); 121 lbs; no capacity stated.. Checked .
  13. Wall Mounted Plate Storage | REP Fitness, REP Fitness. Used for: Horns 8.25 in long; "16” stud mount spacing"; single horn for full sized plates, double horn for change plates; full size plates "will not fit" on the double horn; no capacity stated.. Checked .
  14. Horizontal Weight Plate Storage With Wheels, Titan Fitness. Used for: Toast rack: 8 pockets, small 8.5 in and large 11.75 in wide, 550 lb capacity, 54 x 16 x 12.5 in, 44 lb.. Checked .
  15. Care Information | Eleiko, Eleiko. Used for: "Do not store bars with weights loaded as this could cause the bar to bend." Discs "shall be used and stored in an indoor climate that is dry, clean and holds room temperate (ca. 18-27°C)"; "Don’t allow discs to get wet.". Checked .
  16. Home Gym Maintenance Guide: 7 Ways to Care for Your Equipment, REP Fitness. Used for: Avoid "leaving a bar loaded with weight plates while racked for long periods"; garages "especially vulnerable"; steel corrosion accelerates "when relative humidity exceeds 50 to 60 percent"; dehumidifier; 3-in-1 oil on bare metal; desiccant packs; fans; dry after cleaning; plates scattered on the floor "a recipe for damage".. Checked .
  17. Can bumper plates be left outside? - Fringe Sport, Fringe Sport. Used for: Fringe answers "no" to leaving bumpers outside; "If you're leaving them in direct sunlight especially, they'll reach extremely high temperatures"; if repeatedly exposed, "the inner ring might show signs of stress and rust".. Checked .
  18. Bumper Plate Cleaning Guide, Homegrown Lifting. Used for: HGL URA-MAX bumpers "safe to leave/store outdoors"; UV "can cause urethane bumper plates to fade in color, leading to cracking in virgin rubber bumper plates"; dry wet plates with a towel.. Checked .
Copyright 2026 Basalt Fitness LLC. Every figure we measured carries its date and method, and preliminary ones say so.