Signature Fitness 1 inch standard bars, 5, 6 and 7 ft, are available now on eBay. Checkout on this site opens later.

Weight Plate Dimensions

Weight plate dimensions depend on the hole and the material. Standard plates have a 1 inch center hole and Olympic plates a 2 inch hole, which Titan Fitness and Eleiko state as 50.5 mm. A 45 lb iron Olympic plate from York or Body-Solid is 17 1/2 inches across and 1 1/2 inches thick. American Barbell and Eleiko bumper plates are 450 mm across from 10 lb or 10 kg up, and only their thickness grows with weight.

Updated . By the BASALT editorial team.

A weight plate has three dimensions that matter: the center hole, which decides which bar it fits, the diameter, and the thickness, which decides how many plates fit on a sleeve. Standard plates have a 1 inch hole and Olympic plates a 2 inch hole. A 45 lb iron Olympic plate from York or Body-Solid is 17 1/2 inches across, and Titan Fitness gives up to 454 mm for its iron plates, while the bumper plates from American Barbell and Eleiko are all 450 mm across from 10 lb or 10 kg up. Every plate figure below is the maker's own or a rule book's, read on 17 Nov 2026; the unit conversions and arithmetic are ours. We measured none of these plates.

The center hole decides which bar a plate fits

Plates come in two hole sizes, and each fits one kind of bar. Body-Solid puts it plainly on its standard plate page: "Standard Plates have a 1" center hole; Olympic Plates have a 2" center hole". A plate fits a bar when its hole is a little larger than the bar's sleeve, the part the plates slide onto. A 1 inch plate cannot go onto a 2 inch sleeve at all. A 2 inch plate slides onto a 1 inch sleeve but sits loose, which is why adapter sleeves exist; our bar and plate fit guide covers when one is worth it.

The "2 inch" name is close to the real hole, not exact. An inch is exactly 25.4 mm, so 2 inches is 50.8 mm. Here is what the makers and rule books we read state for the hole and for the sleeve it goes on:

Center hole and sleeve figures as each maker or rule book states them, read 17 Nov 2026. Millimeter equivalents of inch figures are our conversions at 25.4 mm to the inch.
SourceWhat it coversFigure stated
Plate holes
Body-SolidRPB cast iron standard plates1 inch center hole (25.4 mm)
Body-SolidOPB cast iron Olympic plates2 inch diameter center (nominal, no millimeter figure given)
Titan FitnessCast iron Olympic platesCollar opening 50.5 mm, plus or minus 0.2 mm
EleikoIWF weightlifting competition plates (bumper)50.5 mm centre hole, stated as plus or minus 0.5 percent
IPF Technical Rulebook 2026Powerlifting competition discs52 to 53 mm
Sleeves the plates go on
IWF rules 2024Men's and women's competition bars5 cm (50 mm) sleeve diameter
IPF Technical Rulebook 2026Powerlifting bar50 to 52 mm sleeve diameter

Two things follow. First, the Titan and Eleiko holes, at 50.5 mm, are a little under a true 2 inches, while the IPF's 52 to 53 mm is a little over. Second, a plate built to the IPF rule has more room around a 50 mm sleeve than a 50.5 mm plate does. The limits also show why the hole has to suit the sleeve: a 50.5 mm hole clears the IWF's 50 mm sleeve, but the IPF allows sleeves up to 52 mm, which a 50.5 mm hole would not clear, and the IPF's own 52 to 53 mm holes clear any sleeve its rule allows. None of these 2 inch plates sits snugly on a 1 inch bar. If you are not sure which bar you have, our Olympic vs standard barbell guide has a quick check.

1 inch standard plate dimensions

Standard plates have a 1 inch hole and are made for 1 inch bars like the Signature Fitness 5, 6 and 7 ft bars we sell. The three cast iron lines below show how much their size changes by brand and style: York Barbell's two 1 inch lines, Flat Pro and Contour, and Body-Solid's RPB line. York's pages give diameter and thickness but no hole figure; Body-Solid gives a 1 inch hole.

Diameter by thickness, in inches, from each maker's product page, read 17 Nov 2026. Body-Solid prints its sizes as decimals; York prints fractions.
PlateYork 1 inch Flat ProYork 1 inch ContourBody-Solid RPB
1.25 lb3 7/8 x 1/2not listed4 x 0.4
2.5 lb5 x 5/84 5/8 x 7/85.1 x 0.8
5 lb6 1/4 x 3/45 3/4 x 16.7 x 0.8
7.5 lb7 1/2 x 3/4not listed7.5 x 0.8
10 lb8 x 7/87 3/4 x 18.3 x 0.8
12.5 lbnot listednot listed9 x 1.2
20 lbnot listednot listed9.5 x 1.2
25 lb11 x 1 1/811 x 1 3/811.4 x 1.2
35 lbnot listed13 x 1 1/2not listed
50 lb14 3/8 x 1 1/414 x 1 3/415.4 x 2

The same weight can differ by a good deal. A York 25 lb plate is 11 inches across in both lines, but the Contour plate is 1 3/8 inches thick against 1 1/8 for Flat Pro. At 50 lb, Body-Solid's RPB plate is 15.4 inches across and 2 inches thick, against York Contour's 14 by 1 3/4. Thickness sets how many plates fit on each end of a 1 inch bar, so the line you buy changes that count. Our 5 ft vs 6 ft vs 7 ft barbell guide works out how many York Flat Pro and Contour plates fit per side on each of our bars.

2 inch Olympic iron plate dimensions

Olympic iron plates have a 2 inch hole. In the two lines below the 45 lb plate is 17 1/2 inches across and 1 1/2 inches thick, and Body-Solid also lists a 100 lb plate at the same 17 1/2 inch diameter, 2 1/8 inches thick.

Diameter by thickness, in inches, from York's product page and Body-Solid's OPB data sheet, read 17 Nov 2026. Body-Solid calls thickness width.
PlateYork 2 inch Cast Iron OlympicBody-Solid OPB
2.5 lb5 5/8 x 1/26 1/2 x 1/2
5 lb6 1/2 x 3/48 x 1/2
10 lb7 3/8 x 19 x 3/4
25 lb11 3/8 x 1 3/411 x 1 1/4
35 lb14 1/8 x 1 1/214 1/2 x 1 1/4
45 lb17 1/2 x 1 1/217 1/2 x 1 1/2
100 lbnot listed17 1/2 x 2 1/8

Titan Fitness gives ranges in millimeters for its cast iron Olympic plates, a line it sells in 2.5, 10, 25, 35 and 45 lb: an overall diameter of 162 to 454 mm, an overall width of 12 to 34 mm, and a collar opening of 50.5 mm, plus or minus 0.2 mm. A 17 1/2 inch plate is 444.5 mm across, so the top of Titan's range, 454 mm, is larger across than York's and Body-Solid's 45s.

Notice that York's 25 lb plate, at 1 3/4 inches, is thicker than its 35 and 45 lb plates, at 1 1/2. A heavier plate is not always a thicker one, so check each weight you plan to stack rather than assuming.

Bumper plate dimensions, and why they share one diameter

Bumper plates are rubber plates with a steel insert at the hole, for 2 inch bars: American Barbell describes stainless steel inserts and Eleiko zinced steel hubs. On both bumper lines we read, every plate from 10 lb or 10 kg up is 450 mm across, about 17.7 inches, and only the thickness changes with the weight. American Barbell gives its 450 mm as "IWF Standard".

Thickness from each maker's product page, read 17 Nov 2026. American Barbell gives inches and millimeters; Eleiko gives millimeters. Both pages give thicknesses from 10 lb or 10 kg up.
Maker and linePlateDiameterThickness
American Barbell Black LB Sport Bumper Plates10 lb450 mm1 in (25 mm)
15 lb450 mm1 1/4 in (32 mm)
25 lb450 mm1 7/8 in (47 mm)
35 lb450 mm2 1/4 in (57 mm)
45 lb450 mm2 7/8 in (73 mm)
55 lb450 mm3 1/4 in (83 mm)
Eleiko IWF Weightlifting Competition Plates10 kg450 mm35 mm
15 kg450 mm39 mm
20 kg450 mm50 mm
25 kg450 mm58 mm

Why one diameter. The weightlifting rule book sets it: the IWF's 2024 rules require competition discs of 10 kg and over to be 45 cm across, plus or minus 0.1 cm, whatever their weight. The rule book gives no reason in the passage we read, but the effect follows from the geometry. A loaded bar rests on its largest plates, so its center sits half that plate's diameter off the floor: 225 mm with 450 mm plates. When every plate from the lightest full-size one up shares that diameter, the bar starts at the same height with 10 kg on each end or 100, and when it is dropped the full-size plates meet the floor first, not a smaller plate or the bar.

The cost is thickness. Since the diameter is fixed, a heavier bumper can only get thicker: American Barbell's run from 1 inch at 10 lb to 3 1/4 inches at 55 lb. American Barbell's 45 lb bumper is 2 7/8 inches thick, almost twice the 1 1/2 inches of York's and Body-Solid's 45 lb iron plates. Bumpers fill a sleeve faster, which our bumper vs iron plates guide weighs against the noise and floor protection they give.

Competition plate rules: IWF and IPF

The two international rule books set the sizes of plates used in their competitions, mostly as limits. The IWF governs weightlifting, the snatch and the clean and jerk, and its discs of 10 kg and over must be covered with rubber or plastic. The IPF governs powerlifting.

From the IWF Technical and Competition Rules and Regulations 2024 (Regulation to 3.3.3, Barbell: Competition discs) and the IPF Technical Rulebook effective 1 March 2026 (section 2.3), both read 17 Nov 2026. IWF widths are maximums.
IWF discMaximum widthDiameter
25 kg6.7 cm45 cm
20 kg5.4 cm45 cm
15 kg4.3 cm45 cm
10 kg3.5 cm45 cm
5 kg2.65 cm23 to 26 cm
2.5 kg2.3 cm19 to 22 cm
2 kg2.2 cm15.5 to 19.3 cm
1.5 kg2.0 cm13.9 to 17.5 cm
1 kg1.9 cm11.8 to 16 cm
0.5 kg1.6 cm9.7 to 13.7 cm

Both books use 45 cm for the largest plates, the IPF as a maximum and the IWF as a set size with 0.1 cm of tolerance, and they differ on thickness. The IPF's limits are tighter for 25, 15 and 10 kg discs, at 6, 3 and 3 cm against the IWF's 6.7, 4.3 and 3.5 cm, and looser for 20 kg, at 6 cm against 5.4 cm. Eleiko's competition bumper plates sit inside the IWF limits: 58 mm for the 25 kg against the 6.7 cm maximum.

One weight, three sizes

The difference is easiest to see at a single weight. Here is a 10 lb plate in three forms, from the makers' own figures above.

From York's 1 inch Flat Pro and 2 inch Cast Iron Olympic pages and American Barbell's Black LB Sport Bumper page, read 17 Nov 2026.
10 lb plateHoleDiameterThickness
York 1 inch Flat Pro, ironFor 1 inch bars8 in7/8 in
York 2 inch Cast Iron OlympicFor 2 inch bars7 3/8 in1 in
American Barbell Black LB Sport, bumperFor 2 inch bars450 mm (about 17.7 in)1 in (25 mm)

The bumper is more than twice the diameter of either iron plate, which is what lets a lifter pull a light load from the same height as a heavy one. The iron plates are compact, so more of them fit on a sleeve.

How to measure your own plates

Makers' figures are for their own lines, and as the tables show, the same weight differs from one line to the next. Before you buy more plates or a new bar, measure what you have.

  1. The hole. Measure straight across the center hole with a ruler or, better, a caliper. A hole of about 1 inch takes a 1 inch bar; a hole of about 2 inches takes a 2 inch bar. Then measure the bar's sleeve the same way. The hole has to be larger than the sleeve.
  2. The diameter. Measure across the widest part of the plate, through the center. This matters most for bumpers, where you want the plates you drop to be full size.
  3. The thickness. Stack the plates you plan to load on one side and measure the stack, as our bar length guide suggests, since thickness differs by line and does not always rise with weight. Compare the stack with the sleeve's loadable length, from the inner collar to the end, and leave room for an outer collar.
  4. Write it down. Note each plate's diameter and thickness with its weight, so the next purchase matches. If you are still building a set, our what plates do I need guide suggests a starter set for each kind of bar.

Short answers

What is the diameter of a 45 lb plate?

On York's and Body-Solid's 2 inch iron plates, 17 1/2 inches. Titan Fitness gives up to 454 mm for its largest iron plate, and bumper 45s from American Barbell are 450 mm, about 17.7 inches. For competition plates, the IPF sets 45 cm as the maximum, and the IWF requires 45 cm, plus or minus 0.1 cm, for discs of 10 kg and over.

How big is the hole in a weight plate?

About 1 inch on standard plates and about 2 inches on Olympic plates. Body-Solid states 1 inch and 2 inch holes; Titan Fitness and Eleiko state 50.5 mm for their Olympic plates; the IPF requires 52 to 53 mm on powerlifting competition discs.

How thick is a weight plate?

It depends on the weight and the material. A 45 lb iron Olympic plate from York or Body-Solid is 1 1/2 inches thick, while American Barbell's 45 lb bumper is 2 7/8 inches. On 1 inch plates, a York 25 lb is 1 1/8 inches in the Flat Pro line and 1 3/8 inches in the Contour line.

Why are bumper plates all the same size?

Because the weightlifting rules set one size: the IWF requires competition discs of 10 kg and over to be 45 cm across, and the bumper lines we read from American Barbell and Eleiko are 450 mm from 10 lb or 10 kg up. With one diameter, the bar sits at the same height whatever the load, and the full-size plates meet the floor first when it is dropped.

Do Olympic plates fit a 1 inch bar?

They slide on but sit loose, because a 2 inch hole is about twice the width of a 1 inch sleeve. Standard 1 inch plates never fit a 2 inch Olympic bar. Our bar and plate fit guide explains adapter sleeves.

Related: what plates do I need, bumper plates vs iron plates, do standard plates fit an Olympic bar, 5 ft vs 6 ft vs 7 ft barbell, are weight plates accurate, and the plate calculator.

Sources

We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.

  1. RPB Cast Iron 1" Standard Plates, Body-Solid. Used for: Standard plates have a 1 inch center hole and Olympic plates a 2 inch center hole; RPB sizes (diameter x thickness, inches): 1.25 lb 4 x 0.4, 2.5 lb 5.1 x 0.8, 5 lb 6.7 x 0.8, 7.5 lb 7.5 x 0.8, 10 lb 8.3 x 0.8, 12.5 lb 9 x 1.2, 20 lb 9.5 x 1.2, 25 lb 11.4 x 1.2, 50 lb 15.4 x 2. Checked .
  2. SI Units: Length, NIST. Used for: The inch is exactly 25.4 mm, used for 2 inches = 50.8 mm, 17 1/2 in = 444.5 mm, 450 mm = about 17.7 in, and the 25.4 mm shown for a 1 inch hole. Checked .
  3. OPB Cast Iron Olympic Plates (product data sheet), Body-Solid. Used for: Olympic plates have a 2 inch diameter center; OPB width x diameter: 2.5 lb 1/2 x 6 1/2, 5 lb 1/2 x 8, 10 lb 3/4 x 9, 25 lb 1 1/4 x 11, 35 lb 1 1/4 x 14 1/2, 45 lb 1 1/2 x 17 1/2, 100 lb 2 1/8 x 17 1/2 (inches). Checked .
  4. 245 LB Cast Iron Olympic Plate Set, Titan Fitness. Used for: Overall diameter 162 to 454 mm, overall width 12 to 34 mm, collar opening 50.5 mm plus or minus 0.2 mm; line sold in 2.5, 10, 25, 35 and 45 lb. Checked .
  5. IWF Weightlifting Competition Plate - 25 kg, Eleiko. Used for: 450 mm diameter; 50.5 mm centre hole stated as plus or minus 0.5 percent; thickness 35 mm (10 kg), 39 mm (15 kg), 50 mm (20 kg), 58 mm (25 kg); SBR rubber with zinced steel hubs. Checked .
  6. Technical Rulebook 2026 (effective 01.03.2026), International Powerlifting Federation (IPF). Used for: Section 2.3: disc hole 52 to 53 mm; sleeve diameter 50 to 52 mm; discs of 20 kg and over no more than 6 cm thick, 15 kg and under no more than 3 cm; largest discs no more than 45 cm in diameter. Checked .
  7. Technical and Competition Rules & Regulations 2024, International Weightlifting Federation (IWF), copy hosted by the Polish Weightlifting Federation. Used for: Competition discs: 10 kg and over 45 cm plus or minus 0.1 cm, under 10 kg 45 cm or less; discs of 10 kg and over covered with rubber or plastic; maximum widths and diameters 25 kg 6.7 cm/45 cm, 20 kg 5.4/45, 15 kg 4.3/45, 10 kg 3.5/45, 5 kg 2.65/23 to 26, 2.5 kg 2.3/19 to 22, 2 kg 2.2/15.5 to 19.3, 1.5 kg 2.0/13.9 to 17.5, 1 kg 1.9/11.8 to 16, 0.5 kg 1.6/9.7 to 13.7; bar sleeves 5 cm diameter; collar hole 5 cm; full size 45 cm discs of 5 kg and 2.5 kg provided at the platform; snatch and clean and jerk. Checked .
  8. 1" Standard Flat Pro Cast Iron Plate, York Barbell. Used for: Diameter x thickness (inches): 1 1/4 lb 3 7/8 x 1/2, 2.5 lb 5 x 5/8, 5 lb 6 1/4 x 3/4, 7.5 lb 7 1/2 x 3/4, 10 lb 8 x 7/8, 25 lb 11 x 1 1/8, 50 lb 14 3/8 x 1 1/4; no hole size given. Checked .
  9. 1" Standard Contour Cast Iron Plate, York Barbell. Used for: Diameter x thickness (inches): 2.5 lb 4 5/8 x 7/8, 5 lb 5 3/4 x 1, 10 lb 7 3/4 x 1, 25 lb 11 x 1 3/8, 35 lb 13 x 1 1/2, 50 lb 14 x 1 3/4; no hole size given. Checked .
  10. 2" Cast Iron Olympic Weight Plates, York Barbell. Used for: Diameter x thickness (inches): 2.5 lb 5 5/8 x 1/2, 5 lb 6 1/2 x 3/4, 10 lb 7 3/8 x 1, 25 lb 11 3/8 x 1 3/4, 35 lb 14 1/8 x 1 1/2, 45 lb 17 1/2 x 1 1/2; no hole size given. Checked .
  11. Black LB Sport Bumper Plates, American Barbell. Used for: Diameter 450 mm (IWF Standard); thickness 10 lb 1 in (25 mm), 15 lb 1 1/4 in (32 mm), 25 lb 1 7/8 in (47 mm), 35 lb 2 1/4 in (57 mm), 45 lb 2 7/8 in (73 mm), 55 lb 3 1/4 in (83 mm); stainless steel inserts. Checked .
Copyright 2026 Basalt Fitness LLC. Every figure we measured carries its date and method, and preliminary ones say so.