Signature Fitness 1 inch standard bars, 5, 6 and 7 ft, are available now on eBay. Checkout on this site opens later.

Power Rack Dimensions

Power rack dimensions depend on the model. Of the six home racks whose makers' spec pages we read on 18 Nov 2026, the five that give a height stand 71 to 91 inches tall (180 to 231 cm), and the space between the uprights is 42 to 44 inches wide (107 to 112 cm) and 24 to 26 inches deep. A bar must reach past the outside of the uprights, which Titan gives as 46 inches for its T-3.

Updated . By the BASALT editorial team.

On the six home power racks whose spec pages we read, the five that give a height stand 71 to 91 inches tall (180 to 231 cm), and the space between the uprights is 42 to 44 inches wide (107 to 112 cm) and 24 to 26 inches deep where the maker gives it. Overall widths labeled as width run from 44.33 to 58.1 inches. For a barbell, the figure that matters is the width across the outside of the uprights: Titan Fitness gives 46 inches for its T-3. Rack figures are the makers' own, read 18 Nov 2026; conversions and arithmetic are ours. We measured none of these racks.

Power rack dimensions by maker

Overall figures are the floor space and height of the whole frame, which can include parts that stick out, such as the weight plate horns Titan lists for the T-2. Inside figures are the clear space between the uprights, where you squat or set a bench. Titan's T-3 page shows how they fit together: an inside width of 42 inches and an outside width of 46 inches, which is 2 inches of upright on each side.

Each maker's own spec page or data sheet, read 18 Nov 2026, in inches. "Footprint as stated" is printed in the maker's order and with its labels; Titan does not say which footprint figure is width. Titan prints the T-2's inside footprint as "42-in. x 26-in."; we read it as width by depth, the order Titan's T-3 page labels. REP calls its inside figures the working area.
RackHeightFootprint as statedInside widthInside depthUprights
Titan Fitness T-2 Series, 71 in7157 x 5042262 x 2
Titan Fitness T-3 Series, 82 in, 24 in deep8254 x 32.7542242 x 3
Titan Fitness T-3 Series, 91 in, 24 in deep9154 x 32.7542242 x 3
REP Fitness PR-11008558.1 wide, 48.5 deep44242 x 2
Body-Solid GPR378 Pro Power Rack8049 L x 46 Wnot statednot stated3 x 3
Marcy Pro PM-5108 Deluxe Cage System (cage only)83.7550.75 L x 44.33 Wnot statednot statednot stated
CAP+ Full Cage (FMI-105F)not in page textnot in page text42not stated3 x 3

Titan also gives an outside depth for the T-3 of 30 inches, against 24 inside, so by our arithmetic the T-3's uprights are 2 inches across the width and 3 inches front to back. REP gives a working height of 79 inches for the PR-1100 inside its 85 inch frame. Rogue Fitness is missing because its site refused our requests on 18 Nov 2026.

Power rack dimensions in centimeters

None of these makers gives the rack's size in metric on the pages we read, so here are the main figures converted at 2.54 cm to the inch and rounded to the nearest centimeter.

Our conversions of the inch figures in the table above, read 18 Nov 2026, rounded to whole centimeters.
RackHeightInside widthInside depthOverall
Titan T-2, 71 in180 cm107 cm66 cm145 x 127 cm
Titan T-3, 82 in208 cm107 cm61 cm137 x 83 cm
Titan T-3, 91 in231 cm107 cm61 cm137 x 83 cm
REP PR-1100216 cm112 cm61 cm148 wide, 123 deep
Body-Solid GPR378203 cmnot statednot stated124 L x 117 W
Marcy Pro PM-5108 cage213 cmnot statednot stated129 L x 113 W
CAP+ Full Cagenot in page text107 cmnot statednot in page text

Power rack height and your ceiling

Some racks come in two heights. Titan's comparison page lists the T-2 at 71 and 83 inches, the T-3 at 82 and 91 inches, the X-3 at 80 and 90 inches bolted down or 82 and 91 inches with flat feet, and its Titan Series at 90 and 100 inches bolted down or 90 inches with flat feet.

Two other heights decide whether a rack works in your room:

Compare both with the ceiling at the exact spot, including beams, ducts and light fittings. We give no minimum ceiling height, because it depends on your height, your lifts and your plates.

Will your bar span the rack

A barbell rests on the J-hooks by its shaft, the part between the collars, with the collars and sleeves outside the uprights. So the gap between the collars must be wider than the rack across the outside of its uprights. Our barbell length guide explains why and has a fit checker that draws a bar against your rack width.

Titan prints this outside width for the T-3. For three other racks it can be worked out from the inside width plus the upright on each side:

Width across the outside of the uprights, in inches. The T-3 figure is Titan's, read 18 Nov 2026; the rest is our arithmetic from the makers' inside widths and upright sizes. Body-Solid and Marcy give only an overall width, 46 and 44.33 inches, which may include parts outside the uprights, so we did not work one out for them.
RackAcross the outside of the uprightsHow we got it
Titan T-346Stated by Titan
Titan T-2about 4642 inside, plus two 2 inch uprights
CAP+ Full Cageabout 4842 inside, plus two 3 inch uprights
REP PR-1100about 4844 working width, plus two 2 inch uprights; REP's page describes working space as the space between the uprights

The bars we sell are Signature Fitness 1 inch standard bars, made for 1 inch plates.

Source: our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. The between-collars figure is the length minus both plate spaces, so it runs to the collars' outer faces; the gap inside the collars is a little less and not yet measured.
Signature Fitness 1 inch barLengthBetween the collars, outer facesPlate space per side
5 ft60 inabout 41 7/8 in9 1/16 in
6 ft70 15/16 inabout 44 11/16 in13 1/8 in
7 ft84 inabout 53 3/4 in15 1/8 in

Set against the four racks in the width table, at about 46 to 48 inches across the uprights, our 1 inch bars are narrower than those racks are built for, except the 7 ft. On those four racks the 5 ft and 6 ft bars would land with their collars on or inside the J-hooks, not outside the uprights, so treat them as bars for floor work or for stands narrow enough to clear their collars. The 7 ft bar's about 53 3/4 inches, from our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry, is about 5 3/4 inches more than 48, by our arithmetic, so it spans all four; since the gap inside its collars is unmeasured, check your own rack with the fit checker. Marcy's PM-5108 page says its bar and safety catches suit 6-foot and 7-foot Olympic barbells; a 1 inch bar of the same nominal length can differ, so go by the bar's between-collars figure, not its length.

How to check a rack against your room

  1. Floor. Tape the rack's overall footprint on the floor.
  2. Width for the bar. The bar sticks out past the uprights on both sides, and you need to stand at each end to load plates. Our length guide gives the room width we allow for each bar length.
  3. Inside depth. Set your bench or squat stance inside a taped box of the rack's inside width and depth.
  4. Ceiling. Take your pull-up and press measurements as above.
  5. Bar. Measure your rack across the outside of the uprights and compare it with your bar's between-collars figure.

If the room is the limit, our apartment home gym guide has a space planner.

Short answers

How tall is a power rack?

The five racks in our table that give a height stand 71 to 91 inches tall, 180 to 231 cm. Titan's comparison page also lists the T-2 at 71 or 83 inches, the T-3 at 82 or 91 inches, and its Titan Series at up to 100 inches bolted down.

How wide is a power rack?

Between the uprights, 42 inches on Titan's T-2 and T-3 and the CAP+ Full Cage, and 44 inches of working width on REP's PR-1100. Overall widths labeled as width run from 44.33 inches on Marcy's PM-5108 cage to 58.1 inches on the PR-1100.

How deep is a power rack?

Inside, 24 to 26 inches on the Titan and REP racks we read. Overall, REP gives 48.5 inches deep for the PR-1100 and Body-Solid 49 inches long for the GPR378.

Will a 1 inch barbell fit a power rack?

Only if it is longer between the collars than the rack is across the outside of its uprights. Of our three Signature Fitness 1 inch bars, only the 7 ft, about 53 3/4 inches to the collars' outer faces on our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry, spans racks of about 46 to 48 inches.

Related: will a 7ft bar fit your rack, apartment home gym, home gym flooring and noise, 5ft vs 6ft vs 7ft barbell, and our 7 ft standard barbell; also squat rack vs power rack, home gym ceiling height and weight bench dimensions.

Sources

We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.

  1. T-2 Series Power Rack, Titan Fitness. Used for: T-2 (71 in option shown): Overall Height 71-in., Max Pull Up Bar Height 69-in., Overall Footprint 57-in x 50-in., Inside Footprint 42-in. x 26-in., Material 2 x 2-in. 14-Ga Steel, Weight Plate Horns listed. Checked .
  2. T-3 Series Power Rack 82" / 24" depth, Titan Fitness. Used for: T-3 82 in: Overall Height 82-in., Max Pull-Up Bar Height 78-in., Overall Footprint 54-in x 32.75-in., Inside Depth 24-in., Outside Depth 30-in., Inside Width 42-in., Outside Width 46-in., Material 2 x 3-in. 11-Ga Steel. Checked .
  3. T-3 Series Power Rack 91" / 24" depth, Titan Fitness. Used for: T-3 91 in: Overall Height 91-in., Max Pull-Up Bar Height 88-in., Overall Footprint 54-in x 32.75-in., Inside Width 42-in., Outside Width 46-in., Inside Depth 24-in., Material 2 x 3-in.. Checked .
  4. Power Rack Comparison, Titan Fitness. Used for: Rack heights: T-2 71 and 83 in; T-3 82 and 91 in; X-3 80 and 90 in bolt down, 82 and 91 in flat foot; Titan Series 90 and 100 in bolt down, 90 in flat foot. Checked .
  5. PR-1100 Home Gym Power Rack, REP Fitness. Used for: Rack Height 85", Rack Width 58.1", Rack Depth 48.5", Working Area 44" W 24" D 79" H, Material 2x2" 14-Gauge Steel; pull-up bar can be affixed inverted for low ceilings and shorter athletes; FAQ: the PR-1000 has "an extra 2” of working space between the uprights" (working space is the space between the uprights). Checked .
  6. GPR378 Pro Power Rack product data sheet, Body-Solid. Used for: Dimensions: 49"L x 46"W x 80"H; Heavy Duty 11-gauge Steel 3" x 3" Mainframe. Checked .
  7. Marcy Pro Deluxe Cage System with Weight Lifting Bench PM-5108, Marcy. Used for: Cage assembled dimension: 50.75"L x 44.33"W x 83.75"H; adjustable bar and safety catches for 6-foot and 7-foot Olympic barbells. Checked .
  8. CAP+ Full Cage, CAP Barbell. Used for: FMI-105F; inside width is 42 inches; posts of 3x3 inch, 11 gauge steel. Checked .
  9. How we measure, BASALT. Used for: Our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry: lengths 60, 70 15/16, 84 in; plate space per side 9 1/16, 13 1/8, 15 1/8 in; between collars to outer faces about 41 7/8, 44 11/16, 53 3/4 in. Checked .
Copyright 2026 Basalt Fitness LLC. Every figure we measured carries its date and method, and preliminary ones say so.