Signature Fitness 1 inch standard bars, 5, 6 and 7 ft, are available now on eBay. Checkout on this site opens later.

How Much Does a Bench Press Bar Weigh?

A bench press bar is a barbell, so its weight depends on which bar it is. The IPF rules set 25 kg for the bar with two 2.5 kg collars, which leaves 20 kg, about 44.09 lb. Of the 8 power bars we read on 19 Nov 2026, 7 state 20 kg and one's product page states 45 lbs. A Texas Bench Bar states 55 lb / 25 kg, and short or budget bars 21 to 40 lb.

Updated . By the BASALT editorial team.

The bar on a bench press station is a barbell, so the answer is whichever barbell is sitting in the hooks. A full-size power bar is 20 kg, about 44.09 lb. That is what the IPF's powerlifting rules work out to and what 7 of the 8 power bars from 5 makers state on the pages we read on 19 Nov 2026. The eighth, the Texas Power Bar Original, is 44 lb / 20 kg on its maker's compare page and 45 lbs on its own product page. Other bars that can sit on a bench state 55 lb, 15 kg, or 21 to 40 lb. Figures are the rule books' or the makers' own unless labelled as ours, and conversions are ours. We weighed none of the makers' bars.

The bar the rules set for the bench press

The International Powerlifting Federation (IPF) runs the bench press as a competition lift. Its Technical Rulebook, effective 1 March 2026, has no separate bench bar: bars that meet its specifications are used "throughout the entire competition and for all lifts". It gives the weight with the collars on. Bar and collars "are to be 25 kg" and each collar must "weigh 2.5 kg", which leaves 20 kg for the bar. The International Weightlifting Federation (IWF) recognises two lifts, neither of them the bench press, but its two bars are here to compare.

IPF Technical Rulebook effective 1 March 2026, sections 2.3 and 2.4. IWF Technical and Competition Rules and Regulations 2024, in the copy hosted by the Polish Weightlifting Federation. Both read 19 Nov 2026. We did not read any newer IWF edition.
RuleIPF powerlifting barIWF men's barIWF women's bar
Weight25 kg with two 2.5 kg collars, so 20 kg bare20 kg15 kg
LengthNot to exceed 2.2 m220 cm201 cm
Bar diameter28 to 29 mm2.8 cm2.5 cm
MarksMachined markings 81 cm apartBlue identification marking at each end and the centreYellow identification marking at each end and the centre

The 81 cm marks matter on the bench: the IPF's bench press rule says the spacing of the hands "shall not exceed 81 cm measured between the forefingers", about 31.9 in.

In pounds: 44 or 45?

20 kg is about 44.09 lb, at 1 lb = 0.45359237 kg. Eleiko prints "20 kg / 44.09 lbs" on its IPF bar sheets. Texas Power Bars prints 44 lb for its PRO and ELITE power bars and 45 lbs on its Original's product page. So 44 and 45 are both in use for a full-size power bar; 45 lb would be about 20.41 kg, a gap of under 1 lb.

What makers state for power bars and general bars

A power bar is the stiff bar built for the squat, bench press and deadlift. The 8 here are the bars their makers sell as powerlifting or power bars with a 28.5 or 29 mm shaft, or no shaft figure stated. The other rows are general and training bars, including CAP's, which has Power in its name but states 21 to 35 lb.

Weights, lengths and diameters as each maker states them, read 19 Nov 2026. "Not stated" means we did not find the figure in the page text we read. Rogue and Mirafit refused our requests that day, so they have no row.
Maker and barStated weightStated lengthStated bar diameter
Power bars
Eleiko IPF Powerlifting Competition Bar20 kg / 44.09 lbs2200 mm / 86.61 in29 mm / 1.14 in
Eleiko IPF Powerlifting Training Bar20 kg / 44.09 lbs2200 mm / 86.61 in29 mm / 1.14 in
Texas Power Bar ELITE 20KG20 kg / 44 lb86.50 in29 mm
Texas Power Bar PRO44 lb / 20 kg86.50 in29 mm
Texas Power Bar Original44 lb / 20 kg on the compare page; 45 lbs on its product page86 in28.5 mm
Vulcan Absolute Powerlifting Bar V2.020 kgNot statedNot stated
Maniak Powerlifting Bar PWR20 kg2200 mm29 mm
Sorinex Bosco Power Bar20 kgNot stated28.5 mm
A bar built for the bench press
Texas Bench Bar55 lb / 25 kg96.5 in30 mm; 30.75 mm in its spec box
General and training bars
Legend Fitness Bearing Bar20 kg86.75 in28 mm
Texas Multi-Purpose Bar44 lb / 20 kg, 33 lb / 15 kg or 22 lb / 10 kg86 in28.5 mm
Body-Solid OB86B, 7 ft44 lb / 19.96 kg86 in30 mm
Body-Solid OB72B, 6 ft40 lb / 18.14 kg72 in30 mm
Body-Solid OB60B, 5 ft30 lb / 13.61 kg60 in30 mm
CAP Olympic ECO Power Barbell Bar21 or 25 lb (60 in), 27 or 28 lb (72 in), 35 lb (84 in)60, 72 or 84 inNot stated

Seven of the 8 power bars state 20 kg on every page we read, and the eighth on one of its two pages. The other bars do not agree: a full-length bar states 20 kg from Legend, 44 lb / 19.96 kg from Body-Solid and 35 lb from CAP, and the 5 and 6 ft bars state 21 to 40 lb. Length alone does not settle the weight.

Bench bars, bars in rails and 1 inch bars

One dedicated bench bar is heavier. Texas Power Bars states 55 lb / 25 kg for its Texas Bench Bar, 96.5 in long against 86 to 86.50 in for its three power bars above. The maker says it is used "in bench-only meets or specific federations that utilize a 25kg bench bar". Watson's Cambered Bench Press Bar, also built for the lift, states 20 kg, with fixed, non-revolving ends.

A bar in rails is not a barbell. On a Smith machine or another fixed-path station the bar runs in rails, so what you lift with no plates on is the machine's starting weight, which can differ from the bar's own weight. Our Smith machine bar weight guide lists makers' figures by model.

A 1 inch standard bar is lighter. The three Signature Fitness 1 inch bars we sell weighed about 12.4 lb (5 ft), 14.5 lb (6 ft) and 17.9 lb (7 ft): our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. They take plates with a 1 inch hole, not 2 inch plates, and we print no load rating for them, so we give no bench press limit either.

How to tell which bar is on the bench

  1. Read the end of the sleeve and its inner collar. A bar may carry its weight there. Strength Shop's page for the Riot Weightlifting Bar V2 says the blue end cap "repeats the 20 kg weight" and that the name, weight and shaft diameter are laser engraved on the inside face of the sleeve collar. Eleiko says gold-coloured accents mark its IPF competition bar and silver-coloured elements its IPF training bar. The IWF's blue and yellow marks are in the table above.
  2. Measure the length. About 2.2 m, or 86 to 86.75 in, matches every 20 kg bar in the table that states a length. 201 cm, about 79.1 in, is the 15 kg women's size. 60 or 72 in points to the short bars above, 21 to 40 lb, and 96.5 in to the Texas Bench Bar. A long bar can still be lighter: CAP's 84 in bar states 35 lb, and Texas Power Bars lists its 86 in Multi-Purpose Bar at 33 lb / 15 kg and 22 lb / 10 kg as well as 44 lb / 20 kg.
  3. Check the sleeves. The IPF sets 50 to 52 mm and the IWF 5 cm, the size sold as 2 inch. If a bar takes only plates with a 1 inch hole, it is a 1 inch standard bar like ours.
  4. Look at the grip marks. Markings 81 cm apart are the IPF spacing. They show the type of bar, not the weight.

At a gym, the same four checks apply. We give no gym chain's bar weight, because we have not read one published by a chain. Ask the staff which bar it is, or check it yourself.

How to weigh it, and count it

If nothing on the bar gives its weight, weigh yourself on a bathroom scale, weigh yourself again holding the bar, and subtract. Our how to weigh your weights guide covers the method and its limits.

The bar counts toward the lift. A 20 kg bar with a 20 kg plate on each side is 60 kg, and with the two 2.5 kg collars the IPF requires it is 65 kg. The plate calculator has an "Another Olympic bar: enter its weight" choice for a bar that is not 20 kg. For every other bar type, see how much does a barbell weigh.

Short answers

How much does a bench press bar weigh without weights?

20 kg, about 44.09 lb, if it is a full-size power bar. The IPF rules set 25 kg for the bar with two 2.5 kg collars, and 7 of the 8 power bars we read state 20 kg. The Texas Bench Bar states 55 lb / 25 kg, and short and budget bars 21 to 40 lb.

How much does a bench press bar weigh in kg?

20 kg for the bar the IPF rules describe and for the IWF men's bar. The IWF women's bar is 15 kg, and the Texas Bench Bar, built for the lift, states 25 kg.

How much does a bench press bar weigh in pounds?

About 44.09 lb for a 20 kg bar. Texas Power Bars prints 44 lb for its PRO and ELITE power bars and 45 lbs on its Original's product page, so both 44 and 45 are in use for a full-size power bar.

How much does a bench press bar weigh at the gym?

It depends on which bar the gym has put on the bench. We give no gym chain's figure. Check the end cap, measure the length, or weigh the bar. A bar in rails is a machine, and the machine sets the weight.

Related: Olympic vs standard barbell, weight bench dimensions, how to load a barbell and the one rep max calculator.

Sources

We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.

  1. IPF Technical Rulebook, effective 1 March 2026, sections 2.3 Bars and discs, 2.4 Collars and 4.2 Bench press, International Powerlifting Federation. Used for: Bar and collars are to be 25 kg and collars must weigh 2.5 kg each, so a 20 kg bar; bars that meet the specifications are used throughout the entire competition and for all lifts; total length not to exceed 2.2 m; bar diameter 28 to 29 mm; sleeve diameter 50 to 52 mm; machined markings 81 cm apart; collars shall always be used; bench press hand spacing shall not exceed 81 cm measured between the forefingers. Checked .
  2. IWF Technical and Competition Rules and Regulations 2024, sections 2.1 and 3.3.3 and the men's and women's bar specifications, copy hosted by the Polish Weightlifting Federation, International Weightlifting Federation. Used for: The IWF recognises two lifts, the snatch and the clean and jerk; men's bar 20 kg, 220 cm, grip 2.8 cm, sleeves 5 cm, blue identification marking at each end and the centre; women's bar 15 kg, 201 cm, grip 2.5 cm, sleeves 5 cm, yellow identification marking. Checked .
  3. NIST Handbook 44, 2026, Appendix B: Units and Systems of Measurement, National Institute of Standards and Technology. Used for: 1 avoirdupois pound = 0.45359237 kilogram and 1 inch = 25.4 millimeters, for our conversions: 20 kg about 44.09 lb, 45 lb about 20.41 kg, 81 cm about 31.9 in, 201 cm about 79.1 in. Checked .
  4. Eleiko IPF Powerlifting Competition Bar 20 kg, product sheet (3085900), Eleiko. Used for: 20 kg / 44.09 lbs, 2200 mm / 86.61 in, grip diameter 29 mm / 1.14 in; gold-coloured accents mark the bar as IPF competition-certified; built for deadlifts, bench presses and squats with a shaft that stays rigid. Checked .
  5. Eleiko IPF Powerlifting Training Bar 20 kg, product sheet (3085914), Eleiko. Used for: 20 kg / 44.09 lbs, 2200 mm / 86.61 in, grip diameter 29 mm / 1.14 in; silver-coloured elements identify it as IPF-certified training equipment. Checked .
  6. Compare All Texas Barbells, Texas Power Bars. Used for: ELITE 20KG 20 kg / 44 lb, 86.50 in, 29 mm; PRO 44 lb / 20 kg, 86.50 in, 29 mm; Original 44 lb / 20 kg, 86 in, 28.5 mm; Multi-Purpose Bar 44 lb / 20 kg, 33 lb / 15 kg and 22 lb / 10 kg, 86 in, 28.5 mm; Texas Bench Bar 55 lb / 25 kg, 96.50 in, 30 mm. Checked .
  7. Original Texas Power Bar, Texas Power Bars. Used for: The Original's own product page states Weight: 45 lbs, diameter 28.5 mm and overall length 86 in, and no kilogram figure for the Original; its three-bar comparison gives bar weight 45 lbs for the Original, 44 lbs for the PRO and 20 kg for the ELITE. Checked .
  8. Texas Bench Bar, Texas Power Bars. Used for: 55 lb / 25 kg, overall length 96.5 in, 30 mm shaft in the description and 30.75 mm in the spec box; used in bench-only meets or specific federations that utilize a 25kg bench bar. Checked .
  9. Vulcan Absolute Powerlifting Bar V2.0, Vulcan Strength. Used for: A 20 kg powerlifting bar; no length or bar diameter in the page text we read. Checked .
  10. Powerlifting Bar PWR - 29mm - 1200KG, Maniak Fitness. Used for: 20 kg, total length 2200 mm, shaft diameter 29 mm. Checked .
  11. Sorinex Standard Series Bosco Power Bar, Sorinex. Used for: Sold as a power bar; weight 20 KG, diameter 28.5 mm, no overall length stated. Checked .
  12. Legend Fitness Bearing Bar, Legend Fitness. Used for: A 20 kg bar, total length 86.75 inches, 28 mm diameter. Checked .
  13. OB86B 2" Olympic 7' Bar, Body-Solid. Used for: 44 lb / 19.96 kg, 86 in, bar diameter 30 mm, sold as a 2 inch Olympic bar. Checked .
  14. OB72B 2" Olympic 6' Bar, Body-Solid. Used for: 40 lb / 18.14 kg, 72 in, bar diameter 30 mm. Checked .
  15. OB60B 2" Olympic 5' Bar, Body-Solid. Used for: 30 lb / 13.61 kg, 60 in, bar diameter 30 mm. Checked .
  16. CAP Olympic ECO Power Barbell Bar, CAP Barbell. Used for: Versions of 60 in at 21 lb and 25 lb, 72 in at 27 lb and 28 lb, and 84 in at 35 lb; accommodates 2 inch Olympic plates. Checked .
  17. Cambered Bench Press Bar, Watson Gym Equipment. Used for: Weight 20 kg; fixed, non-revolving ends. Checked .
  18. Riot Weightlifting Bar V2, 20 kg - IWF Men's Spec, Strength Shop. Used for: The blue end cap repeats the 20 kg weight; the bar name, weight and shaft diameter are laser engraved on the inside face of the sleeve collar. Checked .
  19. How we measure, BASALT. Used for: Our three Signature Fitness 1 inch bars' weights, 5, 6 and 7 ft: our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. Checked .
  20. Smith Machine Bar Weight, BASALT. Used for: On a Smith machine what you lift with no plates on is the machine's starting weight, which can differ from the bar's own weight. Checked .
Copyright 2026 Basalt Fitness LLC. Every figure we measured carries its date and method, and preliminary ones say so.