Signature Fitness 1 inch standard bars, 5, 6 and 7 ft, are available now on eBay. Checkout on this site opens later.

Deadlift Platform Dimensions

We found no standard deadlift platform size outside the rule books. Across 16 platform sizes from 6 makers, read on 19 Nov 2026, footprints run from 75 5/8 by 27 13/16 inches to 111.5 by 100.6 inches, and the three sold as deadlift platforms are about 8 ft by 4 to 5 ft. The IPF competition platform is between 2.5 m and 4.0 m per side and no more than 10 cm high.

Updated . By the BASALT editorial team.

We read 16 platform sizes on 6 makers' own product pages and sheets on 19 Nov 2026, and the IPF and IWF rule books. 12 of the 16 have one side between 95.75 and 100.6 inches, about 8 feet. Below are each maker's stated footprint, height and weight, the rule book sizes, and how plywood and stall mats tile. We measured none of these platforms; conversions are ours.

Deadlift platform size by maker

Makers label the sides differently: Titan and Rogue call the long side length, while Eleiko, Atlantis and Bells of Steel call it width.

From each maker's product page or product sheet, read 19 Nov 2026. Inch and metric pairs are the maker's own. "Not stated" means the page's text and spec table give no figure. Rogue's row is from Rogue's Canadian site.
Maker and modelFootprint, long side firstHeightWeightBuild, as stated
Sold as deadlift platforms
Titan Fitness Deadlift Platform99 x 59.5 in overall, 94.5 x 47.5 in inside5 in overall110 lb11 gauge steel frame, bare or with four or eight rubber tiles
Rogue Deadlift Platform8 ft 4 in x 4 ft 4 inNot statedNot stated11-gauge steel frame; rubber tiles not included
Eleiko SVR Platform Deadlift2465 mm / 97.05 in x 1420 mm / 55.91 in105 mm / 4.13 in209 kg / 460.77 lbsWood deck, drop zone rubber, 11-gauge steel frame
Bells of Steel Weightlifting Platform, 8 configurations
Single layer: 3, 6 or 9 Square75 5/8 in x 27 13/16, 51 3/4 or 75 5/8 in1 15/16 in / 50 mmNot statedWood centre, rubber outer squares
Single layer: 4, 8 or 12 Square99 1/2 in x 27 13/16, 51 3/4 or 75 5/8 in1 15/16 in / 50 mmNot statedWood centre, rubber outer squares
3 Layer: 3 or 4 Square75 5/8 or 99 1/2 in x 27 13/16 in6 in / 150 mmNot statedWood centre; outer pads of foam in a polyester cover
Other lifting platforms
Atlantis B4800243.2 cm / 95.75 in x 135.3 cm / 53.25 inNot stated226.8 kg / 500 lbMaple wood surface, steel frame
Atlantis B7200243.2 cm / 95.75 in x 193.7 cm / 76.25 inNot stated322 kg / 710 lbMaple wood surface, steel frame
Titan Fitness 8 FT Olympic Lifting Platform98.5 x 98.5 in overall, 94.5 x 94.5 in inside2 in105 lb11 gauge steel frame; tiles sold separately
Legend Fitness Standard Lifting Platform (6 x 8)100.6 x 87.5 in3 in1036 lbs shipping weightLaminated birch, rubber, 11 gauge steel frame
Legend Fitness Standard Lifting Platform (8 x 8)111.5 x 100.6 in3 in1175 lbs shipping weightLaminated birch, rubber, 11 gauge steel frame

The three sold as deadlift platforms are 97.05 to 100 in on the long side and 52 to 59.5 in on the short side: about 8 ft by 4 to 5 ft. Rogue's page also calls its frame "The 8' x 4' Rogue Deadlift Platform", so 8 by 4 is the nominal size, not the footprint. Weights are not like for like: Titan's 105 lb is a bare steel frame, and its Deadlift Platform page does not say which of its three options the 110 lb is for; Eleiko's and Atlantis's platforms have a wood deck, and Legend prints shipping weights only.

Deadlift platform height

Stated heights run from 1 15/16 in for Bells of Steel's single layer builds to 6 in for its 3 Layer builds. Legend's platforms are 3 in thick and Eleiko's is 105 mm, or 4.13 in. Titan states 2 in for its 8 FT frame and 5 in overall for its Deadlift Platform, which uses the same 2 in steel; the page does not say what the 5 in is measured to. Titan's rubber tiles are 1.6 in thick and Rogue's 1.5 in. Any height comes off your overhead clearance: see our home gym ceiling height guide.

Competition platform sizes in the rule books

The IPF's rulebook is for powerlifting, where the deadlift is a contest lift. The IWF's rules are for weightlifting, whose two lifts are the snatch and the clean and jerk, so its platform is here for comparison.

IPF Technical Rulebook dated 01.03.2026, rule 2.2, and IWF Technical and Competition Rules and Regulations 2024, rule 3.3.2, read 19 Nov 2026. The IPF prints metres, the IWF centimetres. Feet and inches are our conversions at 0.3048 m to the foot.
RuleAs printedIn feet and inches
IPF platform"between 2.5 m x 2.5 m minimum and 4.0 m x 4.0 m maximum"; "must not exceed 10 cm in height"About 8 ft 2.4 in to 13 ft 1.5 in per side; about 3.94 in high or less
IWF competition platformSquare, "four hundred (400) cm on each side", "ten (10) cm in height"4 m, about 13 ft 1.5 in per side; about 3.94 in high
IWF training or warm-up platform"three hundred (300) cm wide", two hundred fifty to three hundred cm in lengthAbout 9 ft 10.1 in wide, 8 ft 2.4 in to 9 ft 10.1 in long

The IPF platform is topped with "non-slip smooth carpet", and its rule adds that "Rubber matting or similar sheeting materials are not permitted". The IWF requires hardwood for its competition platform.

Home-built platforms: how plywood and stall mats tile

Neither rule book sets a size for a home-built platform. What is fixed is the size of the sheets it is cut from.

From APA's plywood page and Rubber-Cal's Horse Stall Mat sheet dated August 2021, read 19 Nov 2026. Rubber-Cal's installation note also says "Each mat weighs 100lbs".
SheetSize, as statedThicknessWeight
Plywood panel, per APA"traditional nominal 48 inches by 96 inches"; panels marked Sized for Spacing are slightly less3/4 in in Rogue's layout belowNot stated
Rubber-Cal Horse Stall Mat4ft x 6ft3/4 inch and 1/2 inch90 lbs per 3/4 inch mat, 67 lbs per 1/2 inch mat

The one home-built layout we found in a maker's own words is Rogue's, given as a floor for its frame: Lay 1 full sheet of 3/4" plywood down as the base. Cut two 2' wide strips of stall mat and one 4x4' piece of 3/4" plywood to be used as a top layer. The arithmetic:

Titan's Deadlift Platform is smaller inside than a sheet, 94.5 by 47.5 in against 96 by 48 in, so a full sheet has to be trimmed to fit. Rubber-Cal's sheet prints no size tolerance, so measure before cutting. See our horse stall mats guide and flooring and noise guide.

Bar length against platform width

The IPF rulebook caps a powerlifting bar at 2.2 m overall, about 86.6 in, and the IWF men's bar is 220 cm. On each of the 12 platforms with a side between 95.75 and 100.6 in, that side is longer than 2.2 m; Bells of Steel's 75 5/8 in builds are shorter.

Where the plates land matters more. The IPF sets the distance between a bar's collar faces at 1.31 to 1.32 m, about 51.6 to 52.0 in. Centred over a 48 in wood square, that bar's inner plates start about 1.8 to 2.0 in outside the wood, over the rubber.

The Signature Fitness 1 inch bars we sell are 60 in (5 ft), 70 15/16 in (6 ft) and 84 in (7 ft) long, and length minus both plate spaces leaves about 41 7/8, 44 11/16 and 53 3/4 in between the collars: our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. A 48 in wood centre is wider than the first two spans, so the inner plates of the 5 ft and 6 ft bars would land on wood. For those bars, cut the wood narrower than your span between collars, or cover the whole base with rubber, as Titan's eight tile version does.

The barbell length guide checks a bar against a room and rack, and the Olympic barbell dimensions guide has the 2 inch bar figures.

What we could not read

Rogue's US product page and support guide refused our requests on 19 Nov 2026, so the Rogue figures are from Rogue's Canadian site. The IWF's site also refused us; we read the 2024 rules in the copy the Polish weightlifting federation hosts and could not check for a later edition.

Short answers

What size is a deadlift platform?

We found no standard size outside competition. The three sold as deadlift platforms that we read are 97.05 to 100 in on the long side and 52 to 59.5 in on the short side, about 8 ft by 4 to 5 ft.

What is the competition deadlift platform size?

Between 2.5 m x 2.5 m and 4.0 m x 4.0 m in the IPF rulebook, about 8 ft 2.4 in to 13 ft 1.5 in per side, and no more than 10 cm high.

How thick is a deadlift platform?

Makers state from 1 15/16 in to 6 in. Legend's platforms are 3 in and Eleiko's is 105 mm, or 4.13 in.

What are the Rogue deadlift platform dimensions?

8 ft 4 in long and 4 ft 4 in wide on Rogue's Canadian site, which states no height or weight. Rogue's US page refused our request.

What size is a DIY deadlift platform?

Neither rule book sets one. Built on one plywood sheet it is nominally 48 by 96 in, or 4 ft by 8 ft. Rogue's layout tops that with a 4 by 4 ft plywood centre between two 2 ft wide stall mat strips.

Related: horse stall mats, flooring and noise, ceiling height, will a barbell fit, Olympic barbell dimensions, power rack dimensions.

Sources

We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.

  1. Deadlift Platform, Titan Fitness. Used for: Overall length 99 in, overall width 59.5 in, overall height 5 in, inside length 94.5 in, inside width 47.5 in, product weight 110 lb, 2 in 11 gauge steel frame, 8 ft x 4 ft frame; sold frame only, as a half platform with four rubber tiles and space for plywood in the centre, or as a full platform with eight rubber tiles; one product weight line for all three options, with nothing saying which it is for. Checked .
  2. 8 FT Olympic Lifting Platform, Titan Fitness. Used for: Overall length and width 98.5 in, inside length and width 94.5 in, overall height 2 in, product weight 105 lb, 2 in 11 gauge steel frame, frame only with rubber tiles sold separately; compatible tiles 23.5 x 23.5 in and 1.6 in thick. Checked .
  3. Rogue Deadlift Platform (Rogue's Canadian site), Rogue Fitness. Used for: Length 8 ft 4 in, width 4 ft 4 in, footprint 4 ft 4 in x 8 ft 4 in, 2x2 in 11-gauge steel frame, rubber tiles not included, 24x24x1.5 in rubber tiles, the page's own name 'The 8' x 4' Rogue Deadlift Platform', and the plywood and stall mat layout quoted on the page (one full sheet of 3/4 in plywood as the base, two 2 ft wide stall mat strips and one 4x4 ft piece of 3/4 in plywood as the top layer); no height or weight in the page's text or spec table. Checked .
  4. Eleiko SVR Platform Deadlift, product page, Eleiko. Used for: Product name SVR Platform Deadlift and the link to the product sheet below. Checked .
  5. Eleiko SVR Platform Deadlift, product sheet, Eleiko. Used for: Length 1420 mm / 55.91 in, width 2465 mm / 97.05 in, height 105 mm / 4.13 in, weight 209 kg / 460.77 lbs, wood deck, drop zone rubber, 11-gauge steel frame. Checked .
  6. Weightlifting Platform, Bells of Steel. Used for: 8 configurations: single layer 3, 4, 6, 8, 9 and 12 Square and 3 Layer 3 and 4 Square; assembled widths 75 5/8 in (1921 mm) and 99 1/2 in (2527 mm); assembled depths 27 13/16 in, 51 3/4 in and 75 5/8 in; assembled height 1 15/16 in / 50 mm single layer and 6 in / 150 mm 3 Layer; wood inner squares, rubber outer squares, or polyester covered foam outer pads on the 3 Layer; no weight in the page's text or spec table. Checked .
  7. B4800 Platform with hardwood surface, Atlantis Strength. Used for: Width 243.2 cm / 95.75 in, length 135.3 cm / 53.25 in, weight 226.8 kg / 500 lb, maple wood surface, steel frame contour; no height stated. Checked .
  8. B7200 Platform with hardwood surface, Atlantis Strength. Used for: Width 243.2 cm / 95.75 in, length 193.7 cm / 76.25 in, weight 322 kg / 710 lb, maple wood surface, steel frame contour; no height stated. Checked .
  9. Standard Lifting Platform (6 ft x 8 ft), Model 3131, Legend Fitness. Used for: Dimensions 87.5 x 100.6 x 3 in, shipping weight 1036 lbs, three inches thick, laminated birch footing area, rubber impact areas, 2x3 inch 11 gauge steel frame. Checked .
  10. Standard Lifting Platform (8 ft x 8 ft), Model 3139, Legend Fitness. Used for: Dimensions 111.5 x 100.6 x 3 in, shipping weight 1175 lbs, 3 inches thick, laminated birch footing area, rubber padding on either side, 2x3 inch 11 gauge steel frame. Checked .
  11. IPF Technical Rulebook, effective 01.03.2026, International Powerlifting Federation. Used for: Rule 2.2: platform between 2.5 m x 2.5 m minimum and 4.0 m x 4.0 m maximum, not over 10 cm in height from the surrounding stage or floor, covered with non-slip smooth carpet, rubber matting not permitted. Rule 2.3: bar total overall length not to exceed 2.2 m, distance between the collar faces 1.31 to 1.32 m. The rulebook covers powerlifting, and the deadlift is a contest lift (general rules item 1 (a) and rule 4.3). Checked .
  12. IWF Technical and Competition Rules and Regulations 2024, International Weightlifting Federation (copy hosted by the Polish Weightlifting Federation). Used for: Rule 3.3.2: competition platform square, 400 cm on each side, 10 cm in height; training or warm-up platform 300 cm wide and 250 to 300 cm in length; competition platform of hardwood (Regulation to 3.3.2). The sport of weightlifting's two lifts are the snatch and the clean and jerk (rule 2.1). Men's bar length 220 cm. Checked .
  13. Plywood, APA, The Engineered Wood Association. Used for: The traditional nominal plywood panel size of 48 inches by 96 inches, and that panels marked Sized for Spacing are made slightly smaller. Checked .
  14. Horse Stall Mat Specifications, August 2021, Rubber-Cal. Used for: Stall mat size 4ft x 6ft, thickness 3/4 inch and 1/2 inch, weight 90 lbs per 3/4 inch mat and 67 lbs per 1/2 inch mat, the installation note 'Each mat weighs 100lbs', and no size tolerance printed. Checked .
  15. NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically, NIST. Used for: Foot to metre factor 0.3048 and inch to metre factor 0.0254 (both exact), behind every converted feet and inches figure. Checked .
  16. How we measure, BASALT. Used for: The Signature Fitness 1 inch bars' lengths (60 in, 70 15/16 in, 84 in) and the spans between collars worked from length minus both plate spaces (about 41 7/8, 44 11/16 and 53 3/4 in): our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. Checked .
Copyright 2026 Basalt Fitness LLC. Every figure we measured carries its date and method, and preliminary ones say so.