Safety Squat Bar Weight
A safety squat bar has no standard weight. The 15 bars from 14 makers whose own pages we read on 19 Nov 2026 state from 20 kg, about 44.1 lb, to 31.5 kg, which Vulcan Strength gives as 69 lbs. Six state under 50 lb, three state 50 to 58 lb and six state 65 lb or more, so check your own model before you log a lift.
There is no standard safety squat bar weight. The 15 bars from 14 makers whose own pages we read on 19 Nov 2026 state from 20 kg, about 44.1 lb, to 31.5 kg, which Vulcan Strength gives as 69 lbs. Six state under 50 lb, three state 50 to 58 lb and six state 65 lb or more. None states 45 lb. Every figure below is the maker's own; the conversions are ours. We weighed none of these bars.
Safety squat bar weight by model, in lb and kg
A safety squat bar is the squat bar with handles: a padded yoke sits on your shoulders, two handles point forward, and the ends bend down to the sleeves. Here is what each maker states for the bar alone, without plates. Where a maker gives one unit, the other is our conversion at 0.4535924 kg to the pound.
| Maker and model | Stated weight | Other unit |
|---|---|---|
| Under 50 lb | ||
| Force USA Olympic Safety Squat Barbell | 20 kg | about 44.1 lb |
| Strength Shop Riot Olympic Safety Squat Bar | 20.9 kg | about 46.1 lb |
| Gym Gear Olympic Safety Squat Bar | 21 kg | about 46.3 lb |
| Maniak Fitness Safety Squat Bar | 21 kg | about 46.3 lb |
| Bells of Steel SS4 | 46.3 lbs / 21 kg | |
| Body-Solid OBSS50B | 47 lbs (21 kg) | |
| 50 to 58 lb | ||
| Sorinex Safety Squat Bar | 50 lbs | about 22.7 kg |
| Vulcan Strength One Basic Safety Squat Bar | 25 kg (55 lbs) | |
| Titan Fitness Safety Squat Bar | 58 lb | about 26.3 kg |
| 65 lb and over | ||
| EliteFTS SS Yoke Bar | 65 lbs | about 29.5 kg |
| Watson Safety Squat Bar | 30 kg | about 66.1 lb |
| PRx Performance Safety Squat Bar | 67 lb | about 30.4 kg |
| REP Fitness Safety Squat Bar | 68 lbs | about 30.8 kg |
| Giant Lifting Safety Squat Bar | 69 lb | about 31.3 kg |
| Vulcan Strength Pro Safety Squat Bar | 31.5 kg (69 lbs) | |
The middle figure of the 15 is Vulcan's One Basic at 25 kg. Only Force USA's bar states 20 kg, and nothing sits between Titan's 58 lb and EliteFTS's 65 lbs. A guess can be off by more than 20 lb.
Length, sleeves, rack fit and capacity
Length decides whether the bar fits your room, the sleeve how many plates go on, and the span between the bends whether it sits in your rack.
| Model | Overall length | Sleeve diameter and length | Rack fit, as stated | Stated capacity |
|---|---|---|---|---|
| Force USA | 218 cm | 50 mm, 39 cm loadable | 117 cm between the angled bends on the shaft | 225 kg (500 lbs) |
| Strength Shop Riot | 226 cm | 50 mm, 39 cm loadable | "can be racked with most hooks" | Suggested max load 350 kg |
| Gym Gear | 7 ft 2 in / 220 cm | Sleeve length approx 28 cm | Not stated | Max load 450 kg |
| Maniak Fitness | 2200 mm | 277 mm loadable | Not stated | Maximum load 450 kg |
| Bells of Steel SS4 | 86.61 in / 2,200 mm | 11.81 in / 300 mm loadable | Racks up to 49 in / 1,245 mm between J-cup outer edges | 1,500 lbs / 680 kg |
| Body-Solid OBSS50B | 87 in (2200 mm) | 13 in weight sleeves, for 2 in plates | Not stated | 1000 lbs |
| Sorinex | 87.5 in | 2 in, 16 in length | Not stated | Not stated |
| Vulcan One Basic | 91 in | 16 in loadable | Not stated | 1000 lbs |
| Titan Fitness | 90.5 in | 50 mm, 14.75 in loadable | Rackable width 50 in | 1,500 lb |
| EliteFTS SS Yoke Bar | 92 in | Not stated | 49.5 in between cambers | Not stated |
| Watson | 2250 mm x 550 mm | Not stated | "will fit an Olympic Power Rack" | "will handle over 400 kg" |
| PRx Performance | 90.5 in | 49 mm, 16 in loadable | Sleeve to sleeve 49 in | 1,500 lb |
| REP Fitness | 92.5 in | 2 in, 15.6 in sleeve length | 49.1 in between cambers; REP's 47 in racks and racks up to 49 in wide | Static rating 1,500 lbs |
| Giant Lifting | Not in the page text | 50 mm, 14.75 in loadable | Not in the page text | 1,500 lb static rating |
| Vulcan Pro | 91 in | 16 in loadable | Not stated | 1500 lbs |
Stated lengths run from 218 cm, about 85.8 in, to 92.5 in. Stated sleeve lengths run from Maniak's 277 mm loadable, about 10.9 in, to 16 in on the Sorinex, Vulcan and PRx bars. Every page that states a sleeve or plate size gives 49 or 50 mm sleeves, 2 inch sleeves or 2 inch plates, so a 1 inch plate will not fit. Stated capacity runs from Force USA's 225 kg (500 lbs) to 1,500 lb on six bars.
REP says the distance between the cambers is what allows racking, and that its bar is rackable on its own 47 inch racks and on racks up to 49 inches wide. Force USA's 117 cm between the bends is about 46.1 in. The four racks in the width table of our power rack dimensions guide are about 46 to 48 inches across the outside of the uprights, so measure yours before you buy. Collars differ too: Sorinex says standard spring collars will not work with its bar and EliteFTS says spring collars do not fit, while Strength Shop includes a pair with the Riot bar.
Why safety squat bar weights differ
A straight powerlifting bar has a fixed figure: the International Powerlifting Federation's rulebook sets bar and collars at 25 kg with collars of 2.5 kg each, which leaves 20 kg for the bar, about 44.1 lb. That rulebook does not mention a safety squat bar, and the makers' own lines show what moves the weight:
- Shaft and handle diameter. Vulcan's One Basic and Pro bars state the same 91 in length and 16 in loadable sleeves. The One Basic has a 32 mm shaft and 25 mm handles and states 25 kg; the Pro has a 40 mm shaft and 33 mm handles and states 31.5 kg. The IPF sets its bar diameter at 28 to 29 mm.
- Handles. Vulcan fits solid steel handles 18 in long on both bars. Bells of Steel sells four handle styles and says its end cap gives the exact bar weight with every handle combination, which implies the weight changes with the handles fitted.
- Pad and bends. Watson spreads the load over three pads and states a five inch camber at both ends. Titan states a 5 in drop, REP and Giant 5.5 in.
- Not length on its own. Strength Shop's Riot bar is 226 cm long and states 20.9 kg. Titan's is 90.5 in, about 230 cm, and states 58 lb.
REP says the cambered ends distribute the weight differently than a standard barbell and force the lifter to stay upright, so note the bar next to the number.
What it does to the total you log
The bar counts toward what you lift. A 68 lb REP bar with a 45 lb plate on each side is 158 lb; counted as a 45 lb bar you would write 135 lb, 23 lb short. A 30 kg Watson bar with a 20 kg plate on each side is 70 kg, not 60 kg.
The plate calculator has an "Another Olympic bar: enter its weight" choice in its Bar menu. Pick it and type your bar's stated figure, in your plates' unit, and it loads to your target from that weight. Our how much does a barbell weigh guide covers straight bars, and the trap bar weight guide does the same for hex bars.
Rogue and the pages we could not read
Rogue's product page and its support page for the SB-1 Safety Squat Bar both refused our requests on 19 Nov 2026, so this page prints no Rogue figure rather than one copied from a retailer or a review. Mirafit's page refused as well. If your bar is not in the table, read the maker's own product page, or weigh it.
How to weigh a safety squat bar
- Weigh yourself on a bathroom scale.
- Weigh yourself again holding the bar, with its pad and the handles you train with fitted.
- Subtract. Our how to weigh your weights guide covers the method and its limits.
For comparison, the Signature Fitness 1 inch bars we sell are straight bars with no pad or handles. They weighed about 12.4 lb (5 ft), 14.5 lb (6 ft) and 17.9 lb (7 ft) on our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry, and take 1 inch plates.
Short answers
How much does a safety squat bar weigh?
It depends on the model: the 15 we read state from 20 kg, about 44.1 lb, to 31.5 kg, which Vulcan gives as 69 lbs. Six state under 50 lb, three state 50 to 58 lb and six state 65 lb or more.
What is a safety squat bar's weight in kg?
From 20 kg to 31.5 kg in the makers' figures we read. Force USA states 20 kg, Strength Shop's Riot 20.9 kg, Gym Gear, Maniak and Bells of Steel 21 kg, Vulcan 25 kg or 31.5 kg by model, and Watson 30 kg.
How much does the Titan safety squat bar weigh?
58 lb, about 26.3 kg. Titan's Safety Squat Bar page also states a 90.5 in overall length, a 50 in rackable width and a 1,500 lb capacity.
How much does the SS Yoke Bar weigh?
65 lbs, about 29.5 kg. EliteFTS states that weight for its SS Yoke Bar, with a 92 in length and 49.5 in between the cambers.
Is a safety squat bar 45 lb?
None of the 15 we read states 45 lb. Six state 20 kg to 47 lbs and the other nine state 50 lbs to 31.5 kg, so count your own bar's figure.
Related: trap bar weight, how much does a barbell weigh, power rack dimensions, Smith machine bar weight, how to weigh your weights, and the plate calculator.
Sources
We opened each of these on the date shown and checked the figures on this page against them. Prices and listings change, so follow the links for the current figure. How we write and check guides is in our editorial policy.
- Force USA Olympic Safety Squat Barbell, Force USA. Used for: Bar weight 20 kg; length 218 cm; loadable sleeve length 39 cm; sleeve diameter 50 mm; distance between the angled bend on the shaft 117 cm; max weight 225 kg (500 lbs). Checked .
- Riot Olympic Safety Squat Bar, Strength Shop. Used for: Weight 20.9 kg; length 226 cm; sleeve diameter 50 mm; loadable sleeve length 39 cm; suggested max load 350 kg; can be racked with most hooks; pair of spring collars included. Checked .
- Olympic Safety Squat Bar, spec sheet, Gym Gear. Used for: Bar weight 21 kg; bar length 7ft 2 in / 220 cm; max load 450 kg; length of sleeve approx 28 cm. Checked .
- Safety Squat Bar 21 kilos, Maniak Fitness. Used for: Weight 21 kg; length 2200 mm; loadable length 277 mm; maximum load 450 kg. Checked .
- Safety Squat Bar - The SS4, Bells of Steel. Used for: Weight 46.3 lbs | 21 kg; length 86.61 in / 2,200 mm; loadable sleeve length 11.81 in / 300 mm; max capacity 1,500 lbs / 680 kg; rests in any rack up to 49 in / 1,245 mm between J-cup outer edges; four swappable handle systems; end cap tells the exact bar weight with every handle combo. Checked .
- Safety Squat 2" Olympic Bar OBSS50B, Body-Solid. Used for: Product weight 47 lbs (21 kg); 87 in (2200 mm) long; 13 in weight sleeves; compatible with 2 in Olympic plates; weight capacity 1000 lbs. Checked .
- Safety Squat Bar, Sorinex. Used for: Weight 50 lbs; length 87.5 in; sleeve 2 in diameter, 16 in length; standard spring collars will not work with this bar; no capacity or rack figure in the page text. Checked .
- One Basic Safety Squat Bar, Vulcan Strength. Used for: Barbell weight 25 kg (55 lbs); length 91 in; shaft diameter 32 mm; loadable sleeve length 16 in; solid steel handles, handle length 18 in, handle diameter 25 mm; weight capacity 1000 lbs; all provided measurements are approximations. Checked .
- Pro Safety Squat Barbell with Handles, Vulcan Strength. Used for: Barbell weight 31.5 kg (69 lbs); length 91 in; shaft diameter 40 mm; loadable sleeve length 16 in; solid steel handles, handle length 18 in, handle diameter 33 mm; weight capacity 1500 lbs. Checked .
- Safety Squat Bar, Titan Fitness. Used for: Product weight 58 lb; overall length 90.5 in; sleeve diameter 50 mm; loadable sleeve length 14.75 in; rackable width 50 in; weight capacity 1,500 lb; 5 in drop. Checked .
- SS Yoke Bar, EliteFTS. Used for: Weight 65 lbs; length 92 in; measurement between cambers 49.5 in; spring collars do not fit or work with any specialty bar; no capacity or sleeve figure in the page text. Checked .
- Safety Squat Bar, Watson Gym Equipment. Used for: Weight 30 kg; dimensions 2250 mm x 550 mm; will fit an Olympic Power Rack; will handle over 400 kg; load spread over the 3 pads; five inch camber at both ends. Checked .
- PRx Safety Squat Bar, PRx Performance. Used for: Product weight 67 lb; overall length 90.5 in; sleeve diameter 49 mm; loadable sleeve length 16 in; sleeve to sleeve length 49 in; weight capacity 1,500 lb; produced and shipped from Solid Bar Fitness. Checked .
- Safety Squat Bar, REP Fitness. Used for: Bar weight 68 lbs; length 92.5 in; distance between cambers 49.1 in; camber drop 5.5 in; sleeve length 15.6 in; sleeve diameter 2 in; static rating 1,500 lbs; rackable on REP's 47 in racks and racks up to 49 in wide; the distance between the cambers allows racking; the cambered ends distribute the weight differently than a standard barbell and force the lifter to remain upright. Checked .
- Safety Squat Bar, 69 lb Specialty Barbell, Giant Lifting. Used for: 69 lb; 1,500 lb static rating; sleeves 50 mm diameter, 14.75 in loadable length; 5.5 in drop; no overall length or rack figure in the page text. Checked .
- IPF Technical Rulebook, effective 1 March 2026, International Powerlifting Federation. Used for: Weight of the bar and collars are to be 25 kg; collars must weigh 2.5 kg each (so 20 kg for the bar, our arithmetic); bar diameter 28 to 29 mm; the rulebook's text does not mention a safety squat bar. Checked .
- NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically, National Institute of Standards and Technology. Used for: Pound (avoirdupois) to kilogram factor 0.4535924 and inch to centimeter factor 2.54, behind every figure after "about" (about 44.1 lb, 46.1 lb, 46.3 lb, 66.1 lb, 22.7 kg, 26.3 kg, 29.5 kg, 30.4 kg, 30.8 kg, 31.3 kg, 85.8 in, 10.9 in, 46.1 in, 230 cm). Checked .
- Power Rack Dimensions, BASALT. Used for: The four racks in its width table are about 46 to 48 inches across the outside of the uprights. Checked .
- Barbell Plate Calculator, BASALT. Used for: Its Bar menu has an "Another Olympic bar: enter its weight" choice that takes the bar's weight in the plates' unit (confirmed in the tool's part file, 19 Nov 2026). Checked .
- How we measure, BASALT. Used for: Our Signature Fitness 5, 6 and 7 ft 1 inch bars weighed about 12.4, 14.5 and 17.9 lb, our preliminary check, tape and bathroom scale, 2 Oct 2026, not a Ledger entry. Checked .